Use & care guide

14
Pausing or Restarting
1. To pause the washer at any time, press PAUSE/CANCEL.
2. To continue the cycle, press START (for approximately 1 second).
Changing Cycles, Options, and Modifiers
Not all Options and Modifiers are available with all cycles.
Available modifiers will glow amber. If an option or modifier is
una
vailable with a selected cycle, the light will not illuminate.
Cycles, Options, and Modifiers can be changed anytime before
START is selected.
To cancel a cycle and select a new cycle
1. Press PAUSE/CANCEL twice.
2. Pr
ess POWER.
3. Select desir
ed cycle.
4. Select the desired Options or modifiers such as Water Temp,
Spin Speed, and Soil Level.
5. Press START (for approximately 1 second) to restart the washer
at the beginning of the new cycle.
To cancel a cycle
1. Press PAUSE/CANCEL twice.
2. The washer powers
down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperatur
e is too high, the washer
will drain automatically befo
re the door unlocks.
To change Options or Modifiers after the cycle has
started
1. Press PAUSE/CANCEL once.
2. Select the desir
ed Options or modifiers such as Water Temp,
Spin Speed, and Soil Level. Available
selections will glow amber.
3. Press START (for approximately 1 second) to continue the cycle.
To drain the washer manually
1. Press PAUSE/CANCEL twice.
2. Pr
ess POWER.
3. Select DRAIN/SPIN.
4. Pr
ess START (for approximately 1 second) to begin the drain.
5. When the spin
is complete, the door unlocks. Items can be
removed from the washer.
Status Lights
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Add A Garment
This washer allows a 4-8 minute period in which other garments
may be added to the load. You can add items to the washer if the
Add A Garment status light is glowing.
To add ite
ms when Add A Garment light is glowing
1. Se
lect PAUSE/CANCEL once. The washer door unlocks after
a few seconds, and items can be added.
2. T
o continue the cycle, close the door and select and hold
START (for approximately 1 second).
To add ite
ms when the Add A Garment light is not glowing
1. Y
ou must cancel the current cycle by pressing PAUSE/CANCEL
twice. This will cancel the wash cycle and options. The washer
door unlocks, and items can be added.
2. Close the door
, press POWER, and select the new cycle and
options. Select and hold START (for approximately 1 second).
Done
The Done status light stays on for 60 minutes after the cycle is
complete, and then the washer shuts off.
Sanitized
This washer has a Sanitize water temperature that is certified
by NSF International, an independent thir
d-party testing and
certification organization. The certification verifies that the
sanitizing cycle reduces 99.9% of bacteria typically found
on clothing, bedding, and towels,
and there is no carryover
of bacteria between loads after the cycle is complete.
Certified to Sanitize
If the “Sanitize” wash temperature was selected, when the wash
cyc
le is complete, the DONE status light will illuminate, the door
unlocks, and the wash load can be removed from the washer.
The washer powers down au
tomatically 60 minutes after the
cycle is complete and the DONE status light turns off. Only cycles
with sanitize
wash temperature selected have been designed to
meet the requirements of NSF Protocol P172 for Sanitizing
Efficacy.
Controls Lock/Unlock
The Controls Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When Controls Lock is lit, all
buttons are disabled except for Pau
se/Cancel and Start. You can
lock the controls while the washer is operating.
To lock the controls
Press and hold CONTROLS LOCK/UNLOCK for 3 seconds after the
c
ycle starts, or when the washer is turned off.
The status light next to the CONTROLS LOCK/UNLOCK button
will glow.