Setup and user guide

ManualsBrandsWhirlpool ManualsDomestic AppliancesW5 721E W

Quick guide

* Available only on certain models

FIRST TIME USE

Wait at least two hours, after the installation, before connecting

the appliance to the power supply. Connect the appliance to the

power supply it starts the operation automatically. The ideal storage

temperatures for the food are preset in the factory.

After turning the appliance on, you must wait for 4-6 hours for the

correct storage temperature to be reached for a normally lled

appliance.

CONTROLPANEL

1. Indicator Leds (to display the current temperature set point or the Fast Cooling

function)

2. Fast Cooling Button/Temperature Button

TEMPERATURESETTING

Press the Temperature button on the control panel to adjust the

temperature from the warmest through the lower to the coldest

level. Pressing the Temperature button, the temperature setting will

change cyclically. At rst plug-in of appliance temperature setpoint is

present at medium position (factory setting). Following table shows

temperature setpoints:

OFF ON

Hightemp.

Med-high temp.

Medium temp.

Med-low temp.

Low temp.

Fast cooling

Note: Displayed set points correspond to the average temperature

throughout the whole refrigerator.

FASTCOOLING

The use of the Fast Cooling function is recommended to increase the

cooling capacity of the refrigerator compartment when placing a very

high quantity of food within it.

To activate the Fast Cooling function, press and hold for 3 seconds the

Temperature button on the control panel till all the 3 LEDs will turn on.

The function is automatically deactivated after 24 hours and return to

previous selected set point.

The function can be manually deactivated by pressing and holding for

3 seconds the Temperature button on the control panel.

Note: Fast Cooling function should be also switched ON before placing

fresh food to be frozen in the freezer compartment, in order to maximize

the freezing capacity.

FAN*

The Fan improves temperature distribution inside the product,

allowing better preservation of stored food.

By default, the fan is switched on. To turn o the fan press the button

located on the bottom right corner of fan housing. If the ambient

temperature exceeds 27°C, or if drops of water are present on the

glass shelves, it is essential that the fan is on to ensure the proper

preservation of the food. Deactivation of the fan allows energy

consumption to be optimised. Please note that when the fan is

switched on it will not continuously work. The fan will start/stop

working depending on the temperature and/or humidity level inside

the fridge.

If the appliance has the Fan it can be equipped with the antibacterial

lter. Visit the website page or contact consumer service to purchase

the lter.

LED LIGHT

If the LED light system does not work, please contact the Service to

replace it.

Important: The refrigerator compartment light switches on when

the refrigerator door is opened. If the door is kept open for more than

8 minutes the light will be automatically switched o.

HUMIDITY CONTROL *

Open the humidity regulator (position B) if you want to store food in a

less humid environment like fruit, or close it (position A) to store food

in a more humid environment like vegetable.

TUCK SHELF *

Thanks to the rail system, this shelf allows you to slide under the front

part, creating an extra space for storing tall bottles or pitchers.

Summary of content (3 pages)

PAGE 1
EN Quick guide FIRST TIME USE Wait at least two hours, after the installation, before connecting the appliance to the power supply. Connect the appliance to the power supply it starts the operation automatically. The ideal storage temperatures for the food are preset in the factory. After turning the appliance on, you must wait for 4-6 hours for the correct storage temperature to be reached for a normally filled appliance. CONTROLPANEL 1.
PAGE 2
NO-FROST REFRIGERATOR COMPARTMENT Refrigerator compartment defrosting is completely automatic. Droplets of water on the rear wall inside the refrigerator compartment indicate that the automatic defrost phase is in progress. The defrost water is automatically run into a drain hole and collected in a container, where it evaporates. DEFROSTING THE FREEZER COMPARTMENT The freezer should be defrosted once or twice a year or when excessive frost is present (3 mm thickness). The formation of frost is normal.
PAGE 3
ALARM TABLE Alarm type Signal Cause Cure Door open alarm Refrigerator Light blinks. The door has remained open for more than 5 minutes. Close the door. Door open alarm. Refrigerator Light OFF. The door has remained open for more than 8 minutes. Close the door. Malfunction Product malfunction. Product malfunction. Contact the After-sales Service. TROUBLESHOOTING What to do if... Possible reasons Solutions The appliance is not working. There may be an appliance power supply problem.