Dimensions Guide

2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■ Tape measure
■
1
/
4
" (6.35 mm) cnut driver
■ Marker or pencil
■ Pliers
■ Flat-blade screwdriver
Parts supplied
■ Foam strip roll
■ Clamping brackets (2)
■ 2½" (6.4 cm) clamping
■ screws (2)
Parts needed
■ A UL listed or CSA approved connector for ½" (1.3 cm)
diameter conduit
■ UL listed wire connectors
Check local codes. Check existing electrical supply. See the
“Electrical Requirements” section.
It is recommended that all electrical connections be made by a
licensed, qualied electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
When installing cooktop, use minimum dimensions given.
■ To eliminate the risk of burns or re by reaching over the
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5” (12.7 cm)
beyond the bottom of the cabinets.
■ The cooktop must be a specied cooktop that is approved
to be installed either alone or over an undercounter built-in
oven. Check the cooktop base for an approved installation
label. If you do not nd this label, contact your dealer to
conrm that your cooktop is approved.
■ The cooktop must be installed in a level countertop.
■ Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do
not nd this label, contact your dealer to conrm that your
oven is approved. Refer to oven manufacturer’s Installation
Instructions for approval for built-in undercounter use and
proper cutout dimensions.
■ The cooktop should be installed away from strong draft
areas, such as windows, doors, fans or strong heating vents.
The cooktop should be located for convenient use in the
kitchen.
■ Use the countertop opening dimensions that are given
with these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
■ Grounded electrical supply is required. See “Electrical
Requirements” section.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate, or sustain other damage.
Product Dimensions
A
B
D
F
E
C
A. Glass depth - black and white models - 21 ³⁄
4
" (55.2 cm)
Glass depth - stainless steel models - 22 ¹⁄
8
" (56.4 cm)
B. Glass width - 24" (60.9 cm) models - 23
13
/
16
" (60.5 cm)
Glass width - 30" (76.2 cm) models - 30
13
/
16
" (78.4 cm)
Glass width - 36" (91.4 cm) models - 36
5
/
16
" (92.3 cm)
C. Frame depth - 20¹⁄
4
" (51.5 cm)
D. Frame width - 24" (60.9 cm) models - 21
59
/
64
" (55.7 cm)
Frame width - 30" (76.2 cm) models - 28
15
/
16
" (73.5 cm)
Frame width - 36" (91.4 cm) models - 34
7
/
16
" (87.5 cm)
E. Cooktop height - 3
3
⁄
4
" (9.6 cm)
Cooktop height lighted knobs - 30" (76.2 cm) models -
4
15
/
16
" (12.55 cm)
Cooktop height lighted knobs - 36" (91.4 cm) models -
4
15
/
16
" (12.55 cm)
F. Cooktop height including conduit (located at rear of cooktop, right
side) - 5
1
⁄
4
” (13.5 cm)
Cooktop height lighted knobs, including conduit (located at rear of
cooktop, right side) - 30" (76.2 cm) models - 5
5
/
16
" (13.5 cm)
Cooktop height lighted knobs, including conduit (located at rear of
cooktop, right side) - 30" (76.2 cm) models - 5
5
/
16
" (13.5 cm)