TABLE OF CONTENTS DISHWASHER Marks Prows Supply Cord Connection INSTALLATION REQUIREMENTS Determine Cabinet Tools and Parts Choose Attachment Option Location Requirements. Prepare Water Supply Line... Drain Requirements... Mace Dishwasher Loss to Water Supply Require rm Cabinet Electrical Requirements Connect to Water Supply . Connect to INSTALLATION INSTRUCTIONS Prepare Cabinet Opening— Make Direct Wire Electrical Connection.
Headlong Beoubmnenk Grounded electrical supply required. Do not run drain lines, water lines or theatricals wiring where they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will bs installed must provide clearance between motor and flooring. Motor should not touch the floor. Do not Install dishwasher over carpeted coiffing. Halter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.
Dl Becudirnenis A new drain hose is supplied with your dishwasher. If drain hose is not long sough, use a new drain hiss with a maximum length of 12 ft (3.7 m} (Part Number 3385556) that meats all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm} drain connector of the dishwasher. Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm} minimum above the floor.
INSTALLATION INSTRUCTIONS % Electrical Shock Hazard Disconnect electrical power at the fuse box or cultural breaker box before Installing dishwasher. Allure to do so can result In death or electrical shock. 1 [ Disconnect power ) Disconnect electrical rowan 8t the Tues box of circuit breaker box before installing dishwasher.
2 | Power Supply Cord-Prepare hole SN Malta cabinet A Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet included with prows supply cord kit. Option B, Direct Wire: Helpful Tip: Wiring the dishwasher will be easier if you route the cable Into the cabinet opening from the right-hand side. 7 Bisect Wire — Drill hole Optional location Proforma [ovation 1% Idem) Drill a 114" (3.8 cm) hole in right-hand cabinet side or rear. Se8 “Product and Cabinet Opening Dimensions" section.
Attach water supply line ) Attach the water supply line (copper tubing or flexible braised line) to the hot water Lina using a connection configuration that is in compliance with local codes and ordinances. The water supply to the dishwasher should have a manual shutoff valve located under the sink. 4 | Route water supply line % % Slowly route water supply line through hole in cabinet.
3 Connect drain hose Lon nest drain ins to west (ee or waste disposer using one ot the fallowing option: + Loot A Weave disposer no alr gan » Option 8. Ne waste disposer approval = Upton €, Wests disposer . with air gap = Orion 1 Mo waste disposer with sl gap J IMPORTANT: Tha drain hiss connection of the disposer or a waste tee must be made before the drain trap and at least 20" (50.8 cm) above the floor where the dishwasher will be Installed.
Option D, No waste disposer with alr gap Frappe Dishwasher Rusher hose connector Tip Over Hazard Bo not use dishwasher until completely installed. P2 not push down on open door. Doing 5o can result In serous Injury or cuts. 1. m::ctanrzh:;r :nng;,f hose to WARN I"G NOTE: Do not cut ribbed section. Excessive Weight Hazard Use two or mots people to move and Install dishwasher. 2 Attach drain hose to air gap with large drain hose clamp (provided). Failure 1o do o can result in back or other injury.
2 Put dishwasher on its balaclava Using 2 or more people, grasp sides of dishwasher door frame and place dishwasher on Its back. 3 Using a fiat-blade screwdriver, turn the plastic fasteners ¥4 tum counterclockwise to unlock them. Remove panel. Do not remove tech sheet from access anal. Using a ¥%4" hex-head socket, nut driver or Torx® T20° screwdriver, remove terminal box cover. Rental for later use. 12 & | Install strain relief 1 Install a UL Listed Approved strain blissful.
Select UL Listed Approved twist-on wire connectors rated to connect your power supply cord to 16-gauge dishwasher wiring. % Electrical Shook Hazard Electrically ground dishwasher. Conn est ground wire to green ground connector In terminal box. Do not use an extension cord. Allure o follow theses Instructions can result In deal, firs, or civically shook. 2 | Power Supply Cord— ‘ — Connect ground wire Remove the ground connector screw and place through the ring terminal of the green ground wire.
Insensate Cockerel Operand Your dishwasher has leveling legs. The following provides instructions to adjust the leveling legs to set the dishwasher to the correct height for your cabinet opening. 1 Measure cabinet opening iy N Measure height of cabinet opening from underside of counter top to floor where dishwasher will be installed (you will need to measures the lowest paint on the underside of the counter top and the highest point on the firewood.
3 | Built-up Floors—Add shims as needed Option 1, Counter top Attachment Built-up floors: If the kitchen orifice is higher than the cabinet opening's floor for examples, the kitchen floor tile doss not extend Into the cabinet opening add shims as needed In the area shown to bring the dishwasher up to 33%" (85.1 ¢m) below the counter top. NOTE: Shims must be securely attached to floor to avoid overtime when the dishwasher is in use.
2| Add 80° skibob fitting to the ) water supply line ‘ 7 ‘ Check water and drain — hose position — Connect the %" compression fitting of the 90° elbow to the water supply line prior to installing the unit into the cabinet opening. Attach such that the 32" connection is facing upward as shown above. Copper tubing only: Put the tubing into the 90° elbow fitting as far as It will go {ths copper tubing bends and kinks measly. Lids the nut and ferrule forward and start the nut onto the slow threads.
5 [ Door falls open " Increase spring tension | 8| Check for plumb and ) * adjust legs if needed A, If the door falls open, increase the spring tension by moving the spring end toward the back of the dishwasher. NOTE: Springs should be in the same notches on left and right sides. & Move dishwasher into} Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is centered from front to back in the opening.
Corrector Weber Supply Connection Din 1 | Tighten 80° elbow fitting to valve ] 1 | Connect drain hose | Be sirs rubber washer Is properly seated In fitting. Side the %' fitting up to the valve and hand tighten to avoid cross threading. Hand tighten until the coupling is tight. Using pliers, check the tightness of the coupling. An additional % to % tum may be required to seal the rubber gasket. NOTE: Do not over tighten. Damages to the coupling can result.
Mok Direct Wire Blucher Conclusion NOTE: If the power supply cord was connected earlier, proceed to “Secure Dishwasher in Cabins Opening” section. Option B, Direct Wire: 4 Direct Wire—Route cable | [ into terminal box ‘ Route cable so that it doss not touch dishwasher mayor or lower part of dishwasher tub. Pull cable through UL Listed Approved strain relief In terminal box. Strain relief Is not supplied with the dishwasher. Owner must purchase a %" screw-in type strain relief.
Connect wires black to black and white to white, using UL Listed Approved twist-on wire connectors (not Included). Wiring configuration Fowler supply wire: Farming box wire: é white e white black=e = back ground wire e s ground conservator If needed, ses website for animated representation of this step. Visit under FAQ tab. 4 Direct Wire—Secure cable in strain relief ‘ Tighten strain relief scows to secure cable. B DirectWire—Reinstall] terminal box cover o X Place wires Inside terminal box.
Check that top of door does not contact screws, brackets or counter top. If it does, adjust invaliding lags. Corrode logrolling Reinstall access panel and fasteners Insulation {on same mandala Place the plastic access panel against the dishwasher leg. 2 | Check access panel edge) E | Check inner spacing ) Open door and check that space between dishwasher cabinet opening and tub is equal on both sides. If spacing is not equal, loosen bracket screws secured and shift tub. Tighten bracket screws.
YT 4 Electrical Shock Hazard Pius Into & grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Bo not use an extension cord. Failure 1o follow these instructions can result in death, fire, or electrical shoe. 1 | Power supply cord—Plug into a grounded 3 prong outlet Plug into a grounded 3 prong loutish. Check that power supply cord doss not touch dishwasher motor or lows part of dishwasher tub.