Instructions for use WASHER-DRYER ! This symbol reminds you to read this instruction manual.
Installation ! Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. GB ! Read these instructions carefully: they contain vital information on installation, use and safety. Unpacking and levelling Unpacking 1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport.
Connecting the drain hose 65 - 100 cm Where it connects to the waste water pipe cut end off spigot or remove the blanking cap Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot.
As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
GB Technical data Model WDI 651 WH width 59.5 cm height 81.5 cm depth 54.5 cm from 1 to 6 kg for the wash Capacity programme; from 1 to 5 kg for the drying programme please refer to the technical Electrical data plate fixed to the maconnections chine maximum pressure 1 MPa (10 bar) Water conminimum pressure 0.05 nection MPa (0.5 bar) drum capacity 52 litres Spin speed up to 1200 rotations per minute Wash: programme 2; temperature 60°C; run with a load of 6 kg.
Instructions for the fitter GB Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely (see figures below).
Using the Drilling Template. - To trace the positions of the holes on the lefthand side of the panel, align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference. - To trace the positions of the holes on the righthand side of the panel, align the drilling template to the top right side of the panel. - Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and the magnet.
Care and maintenance GB Cutting off the water or electricity supply 2. clean the interior thoroughly; 3. screw the lid back on. • Turn off the water tap after every wash. This will limit the wear of your appliance’s water system and also prevent leaks. • Unplug your appliance when cleaning it and during all maintenance operations. Checking the water inlet hose Cleaning your appliance The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water.
Precautions and advice ! The Washer-dryer was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully. General safety • This appliance was designed for domestic use only.
Washer-dryer description FUNCTION Control panel GB ON-OFF/DOOR LOCK Led Buttons Leds ON-OFF Button Detergent dispenser DRYING START/RESET Knob Button TEMPERATURE Knob Detergent dispenser: to add detergent and fabric softener. LEDS: to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated. DRYING knob: to set the desired drying cycle. FUNCTION buttons: to select the functions available.
Leds The LEDS provide important information. This is what they can tell you: Delay set: If the Delay Timer function has been enabled, once you have started the programme, the LED corresponding to the delay set will begin to flash: Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: Prewash / Wash Rinse Spin cycle Drying Note: - during draining, the LED corresponding to the Spin cycle phase will be turned on.
Starting and Programmes Briefly: starting a programme 6. Add the detergent and any fabric softener. 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the Washer-dryer off by pressing button . 1.
Personalisations C Setting the temperature GB Turn the TEMPERATURE knob to set the wash temperature. The temperature can be lowered, or even set to a cold wash ( ). Set the drying cycle Turn the DRYING knob to set the desired drying type. Two options are available: A - Based on time: From 40 minutes to 180. B - Based on the damp level of the dry clothes: Iron : slightly damp clothes, easy to iron. Hanger : dry clothes to put away. Cupboard : very dry clothes, recommended for towelling and bathrobes.
Detergents and laundry Detergent dispenser GB Good washing results also depend on the correct dose of detergent: adding too much detergent won’t necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.
Troubleshooting Your Washer-dryer could fail to work. Before calling for Assistance, make sure the problem can’t easily be solved by consulting the following list. Problem Possible causes/Solution: The machine does not switch on. • The appliance is not plugged into the socket fully, or not enough to make contact. • There is no power to the socket, or the fuse has blown in the mains plug. The wash cycle does not start. • • • • • The machine does not dry. • Check the 2 sections above.
GB The machine is noisy. • There will always be some motor, pump and drum noise during spin. The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly. This is a safety feature to prevent damage.
Service Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. GB ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
GB 18
GB 19
195139074.