Dimension Guide

ManualsBrandsWhirlpool ManualsAppliances51-Decibel Top Control 24-in Built-In Dishwasher (Black) ENERGY STAR

Because Whirlpool Corporation policy includes a continuous commitment to

improve our products, we reserve the right to change materials and specications

without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specications subject to change without notice.

DRAIN REQUIREMENTS

n A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) that meets all current AHAM/

IAPMO test standards, is resistant to heat and detergent, and

ts the 1" (25 mm) drain connector of the dishwasher. See

the “Tools and Parts” section at the front of the guide for part

details and orders.

n Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (508 mm)

minimum above the oor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter or be connected to an air gap.

n Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (508 mm) above suboor or

oor.

Use of air gap

n If required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting

the air gap, a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

n Use 1/2" (13 mm) minimum I.D. drain line ttings.

WATER SUPPLY REQUIREMENTS

n This dishwasher has a water heating feature and also requires

a connection to a hot water supply line.

n A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)

water pressure can be veried by a licensed plumber.

n 120°F (49°C) water at dishwasher.

n 3/8" (9.5 mm) O.D. copper tubing with compression tting or

exible braided water supply line.

NOTE: 1/2" (13 mm) minimum plastic tubing is not

recommended.

n A 90° elbow with 3/4" (19 mm) hose connection with rubber

washer.

n Do not solder within 6" (152 mm) of the water inlet valve.

n If installed in new construction, make sure the house water

supply lines have been ushed prior to connecting the

dishwasher to remove any debris that may exist in the supply

line.

NOTE: If replacing an existing dishwasher, it is recommended

to install a new water line and drain hose (supplied) with the

new dishwasher.

ELECTRICAL REQUIREMENTS

You Must Have:

n 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply

n Copper wire only

n A maximum of 2 eld wiring supply conductors (12 AWG

largest size) plus 1 grounding conductor are permitted in the

terminal box.

We Recommend:

n A time-delay fuse or circuit breaker.

n A separate circuit

If connecting dishwasher with a power supply cord:

n Use UL Listed power cord kit marked for use

with dishwasher.

n Plug into a grounded 3 prong outlet.

Outlet must meet all local codes and

ordinances.

If connecting dishwasher with direct wiring:

n Use exible, armored, or nonmetallic

sheathed copper wire with grounding wire

that meets the wiring requirements for your

home and local codes and ordinances.

n Use a UL Listed/CSA Approved metallic

strain relief.

Air gap

W11462846B

Undercounter Dishwasher

Summary of content (6 pages)

PAGE 1
Undercounter Dishwasher DRAIN REQUIREMENTS n n n A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and fits the 1" (25 mm) drain connector of the dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.
PAGE 2
PRODUCT AND CABINET OPENING DIMENSIONS: . 237/8" (606 mm) 251/4" (641 mm) 3/4" (19 mm) A B 30" (762 mm) 33½" (851 mm) min. with leveling legs removed 30" (762 mm) 33/4" (94 mm) 21" (533 mm) 31/2" - 41/2" (88 mm - 106 mm) A. Insulation may be compressed (not used on all models). B. Door handles may protrude forward of the face of the dishwasher, varies by model. For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (876 mm).
PAGE 3
EXIGENCES D’ÉVACUATION n n n Un tuyau d’évacuation neuf est fourni avec le lave-vaisselle. Si le tuyau d’évacuation n’est pas suffisamment long, utiliser un tuyau d’évacuation neuf d’une longueur maximale de 12 pi (3,7 m) satisfaisant à toutes les normes de test AHAM/ IAPMO en vigueur, qui soit résistant à la chaleur et au détergent et qui convienne au raccord d’évacuation de 1po (25 mm) du lavevaisselle.
PAGE 4
DIMENSIONS D’OUVERTURE DU PRODUIT ET DE L’ARMOIRE : . 25 1/4" (641 mm) 23 7/8" (604 mm) 3/4" (19 mm) A B 30" (762 mm) 33 ½" (851 mm) min. sans pieds de nivellement 30" (762 mm) 3 3/4" (94 mm) 3 1/2" - 4 1/2" (88 mm - 106 mm) 21" (533 mm) A. L’isolant peut être comprimé (utilisé sur certains modèles). B. Les poignées de porte peuvent dépasser vers la façade du lave-vaisselle; varie selon le modèle. Pour un coup-de-pied de 4 po (100 mm), la hauteur de l’ouverture est de 34 1/2 po (876 mm).
PAGE 5
REQUISITOS DE DESAGÜE n n n Se provee una manguera nueva de desagüe con su lavavajillas. Si la manguera de desagüe no es lo suficientemente larga, utilice una manguera de desagüe nueva con una longitud máxima de 12 pies (3,7 m) que cumpla con todos los estándares de comprobación actuales de AHAM/IAMPO, que sea resistente al calor y al detergente y que encaje en el conector de desagüe de 1" (25 mm) de la lavavajillas.
PAGE 6
DIMENSIONES DEL PRODUCTO Y DE LA ABERTURA DEL GABINETE: . 251/4" (641 mm) 237/8" (604 mm) 3/4" (19 mm) A B 30" (762 mm) 33½" (851 mm) min. sin patas niveladoras 30" (762 mm) 33/4" (94 mm) 31/2" - 41/2" (88 mm - 106 mm) 21" (533 mm) Para un zoclo de 4" (100 mm), la altura de la abertura del gabinete es de 341/2" (876 mm). A. El aislante puede estar comprimido (no se utiliza en todos los modelos). B.