Owner's Manual

6
DISHWASHER SETTING MENU:
Follow the below instructions to enter into the menu to change your current settings.
Menu
Display Text
(if display is
present)
LED Pattern (no display)
What this setting does
Default
Setting
PROWASH
OR
SENSOR
TOUGH OR
COOKWARE
NORMAL
Rinse Aid Level A X Adjust amount of rinse aid dispensed
Rinse Aid Level
sub-menu
A 0 X X X 0 mL - rinse aid off
A 1 X 1.3 mL
A 2 X 2.6 mL
A 3 X X 3.9 mL X
A 4 X 5.2 mL
A 5 X X 5.2 mL
A 6 X X 5.2 mL
Sound Level S X X Turn sound On and Off
Sound Level
sub-menul
S 1 X Sound On X
S 0 X Sound Off
Light in Tub L X Turn the inner light on and off (if present)
Lights in Tub
sub-menul
L 1 X Light in Tub ON when door is opened X
L 0 X Light in Tub OFF when door is opened
Kosher
Consumer
Friendly mode
E X X
Turn Kosher Consumer Friendly mode
On and Off
E 1 X Turn mode ON
E 0 X Turn mode OFF X
Factory Reset r X X X Factory Reset
1. Press and hold the “Hi Temp” button for 5 seconds until “Hi Temp” and “Dry” lights turn on.
2. Press the “Start/Resume” button within 2 seconds. If you do not press Start within 2 seconds, then the display will turn off and you
will need to start over and go back to step 1.
a. For Models with a Display, an “A” will show in the display to indicate Rinse Aid Level.
b. For Non-display models,“Tough or Cookware” light will turn on to indicate Rinse Aid Level.
3. To go to a feature other than Rinse Aid Level, press the “Cycle” button or “Normal” button (depending on model) to move to the
feature you would like to change (Sound Level, Light in Tub, Kosher Friendly, Factory Reset, Rinse Aid Level). See the table for what
is shown on the display to indicate these features.
4. Press the “Start/Resume” button to select the feature and enter the sub-menu. The display will change to show the current setting
of the feature. (For example, if you selected Sound Level and you haven’t changed it before, then S1 will show for display models
and sensor will light for non-display models.)
5. Press “Cycle” button or “Normal” button (depending on model) to change the value of the feature setting. (For example, if you want
to turn the sound off, then press the “Cycle” or “Normal” button and S0 shows on display models or “pots and pans” lights for non-
display models.)
6. Press the “Start/Resume” button to conrm the new selection. The feature setting will not be changed until the “Start/Resume”
button is pressed.
The dishwasher will return to the Off state when the Start button is pressed.
To exit the customer settings menu at any time, press the “Cancel” button, or wait 30 seconds without pressing any buttons.
NOTE: To see the current setting of a feature, follow steps 1-4. When the “Start/Resume” button is pressed in step 4, the dishwasher
will show the current setting. Press the “Cancel” button to exit without making any changes.
NOTE: If you enter into a Feature Setting Page and need to go back to the Main Menu Press “Cancel” and proceed to step 1.
NOTE: To exit “Kosher Consumer Friendly Mode” at any time, press the “Cancel” button or you can wait 75 hours.
Kosher Consumer Friendly Mode: When turned on, will disable all of the buttons on the dishwasher except for the cancel key, and
disable the light inside the tub (if equipped) for a time period of 75 hours. If this mode is turned on during a cycle, then the status lights
at the end of cycle will not turn off when the door is opened and then re-closed. To exit this mode, press the “Cancel” button, or wait
75 hours.