Installation Guide

ManualsBrandsWhirlpool ManualsSingle Oven Electric RangesWEE510SAGS

IMPORTANT:

ve for local electrical inspector's use.

IMPORTANT :

À conserver pour consultation par l'inspecteur local des installations électriques.

W11097823A

INSTALLATION INSTRUCTIONS

FRONT CONTROL ELECTRIC RANGES

Table of Contents

RANGE SAFETY .............................................................................2

INSTALLATION REQUIREMENTS ................................................. 3

Tools and Parts .............................................................................3

Location Requirements ................................................................3

Electrical Requirements - U.S.A. Only .........................................5

INSTALLATION INSTRUCTIONS ................................................... 6

Unpack Range..............................................................................6

Install Anti-Tip Bracket .................................................................6

Adjust Leveling Legs ....................................................................7

Level Range .................................................................................. 8

Electrical Connection - U.S.A. Only .............................................8

Verify Anti-Tip Bracket Is Installed and Engaged ......................14

Remove/Reinstall Toe Panel ......................................................14

Oven Door ..................................................................................14

Complete Installation .................................................................15

Summary of content (16 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FRONT CONTROL ELECTRIC RANGES Table of Contents RANGE SAFETY..............................................................................2 INSTALLATION REQUIREMENTS..................................................3 Tools and Parts..............................................................................3 Location Requirements.................................................................3 Electrical Requirements - U.S.A. Only..........................................
PAGE 2
RANGE SAFETY WARNING Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved. Do not operate range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults.
PAGE 3
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Location Requirements IMPORTANT: Observe all governing codes and ordinances. ■■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial/rating plate. The model/serial/rating plate is located behind the oven door on the top right-hand side of the oven frame.
PAGE 4
Mobile Home — Additional Installation Requirements Cabinet Dimensions The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.
PAGE 5
Electrical Requirements — U.S.A. Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord. Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances.
PAGE 6
INSTALLATION INSTRUCTIONS Unpack Range WARNING Install Anti-Tip Bracket WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape, and film from the range. Keep cardboard bottom under range. Do not dispose of anything until the installation is complete. 2. Remove oven racks and parts package from oven and shipping materials. 3.
PAGE 7
4. Drill two 1⁄8" (3 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations. Floor Mounting Adjust Leveling Legs 1. If range height adjustment is necessary, use a wrench or pliers to loosen the four leveling legs. This may be done with the range on its back or with the range supported on two legs after the range has been placed back to a standing position.
PAGE 8
3. Depending on your model, remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. Level Range 1. Place level on the oven bottom, as indicated in one of the two figures below, depending on the size of the level. Check with the level side-to-side and front to back. 2. If range is not level, use a wrench or pliers to adjust leveling legs up or down until the range is level.
PAGE 9
If your home has: And you will be connecting to: Go to Section: 3-wire receptacle (NEMA type 10-50R) A UL Listed, 250-volt minimum, 40- or 50-amp, range power supply cord 3-Wire Connection: Power Supply Cord A UL Listed, 250-volt minimum, 40- or 50-amp, range power supply cord 4-Wire Connection: Power Supply Cord 4-wire receptacle (NEMA type 14-50R) 2. Use 3⁄8" (9.5 mm) nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. A E D B C A.
PAGE 10
2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground link under the screw. 3. Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. Install Using Direct Wire WARNING A B Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range.
PAGE 11
3. Depending on your model, remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. 2. Allow enough slack in the wire to easily attach the wiring terminal block. 3.
PAGE 12
2. Attach terminal lugs to line two (red), bare (green) ground, and line one (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart.
PAGE 13
4. Attach terminal lugs to line one (black), neutral (white), and line two (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart. A 5. Use a hex or Phillips screwdriver to connect the bare (green) ground wire to the range with the ground-link screw and ground-link section.
PAGE 14
Verify Anti-Tip Bracket Is Installed and Engaged 1. Slide range into final location, making sure rear leveling leg slides into anti-tip bracket. 2. Remove the toe panel. 3. Use a flashlight to look underneath the bottom of the range. 4. Visually check that the rear range foot is inserted into the slot of the anti-tip bracket. 5. Replace the toe panel. IMPORTANT: If the range is moved to adjust the leveling legs, verify that the anti-tip bracket is engaged by repeating steps 1 to 5.
PAGE 15
Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Check that you have all of the range accessories, especially oven racks. These accessories may be in the range packaging. 4. Dispose of/recycle all packaging materials. 5. Check that the range is level. See the “Level Range” section. 6.