Service Manual
Table Of Contents
- Service Manual - 27" Gas & Electric Stacked Laundry Center, L-95
- Table of Contents
- Section 1 - General Information
- Section 2 - Diagnostics & Troubleshooting
- Diagnostic Guide
- Diagnostic LED-Main Control
- Self Diagnostic Test Modes (Washer)
- Activating the Service Diagnostic Test Modes (Washer)
- Unsuccessful Entry
- Exiting the Service Diagnostic Test Modes (Washer)
- Customer Viewable Fault Codes (Washer)
- Fault/Error Codes Chart (Washer)
- Automatic Test Mode Chart (Washer)
- Manual Test Mode Chart (Washer)
- Washer Troubleshooting Guide
- Dryer Troubleshooting Guide
- Section 3 - Testing - Washer
- Section 4 - Testing - Dryer
- Section 5 - Component Access
- Product Specifications & Warranty Information Sources
DIAGNOSTICS & TROUBLESHOOTING
27” Stacked Laundry Center
n
2-13
For Service Technician Use Only
Water covering the impeller? See TEST #5: Water Level, page 3-13.
Is lid open during the cycle? Check for interference with lid. Lid must be closed.
Drive belt. Verify that drive belt is not damaged.
Harness connecons. Check harness connecons between main control and drive
system.
Shier problem. See TEST #3a: Drive System – Shier, page 3-8.
Motor problem. See TEST #3b: Drive System – Motor, page 3-10.
Tachometer problem. No tub movement or tub speed out of normal range
(obstrucon/belt/motor).
Main Control problem. See TEST #1: Main Control, page 3-5.
Is lid lock showing open during the
cycle?
See TEST #7: Lid Lock, page 3-15.
Drive belt. Verify that drive belt is not damaged.
Harness connecons. Check harness connecons between main control and drive
system.
Shier problem. See TEST #3a: Drive System – Shier, page 3-8.
Motor problem. See TEST #3b: Drive System – Motor, page 3-10.
Tachometer problem. No tub movement or tub speed out of normal range
(obstrucon/belt/motor).
Main Control problem. See TEST #1: Main Control, page 3-5.
Drain hose installaon. Check for proper drain hose installaon. Make sure it is not
inserted more than 4.5” (114 mm). Make sure drain hose is not
sealed into drain pipe, and that there is an air gap for venlaon.
Standpipe posion. Ensure drain height is between 39” (991 mm) and 8’ (2.4 m)
above the oor.
Plugged drain hose. Check drain hose for obstrucons.
Obstrucons to drain pump. Check tub sump under agitator plate & basket for obstrucons.
Harness connecons. Check harness connecons between main control and drain
pump.
Drain pump. See TEST #6: Drain Pump, page 3-14.
Main Control problem. See TEST #1: Main Control, page 3-5.
Oversuds. 1. Verify use of HE detergent.
2. Excessive detergent usage.
O balance. 1. Load is o balance.
2. Balance ring water leak.
Drain hose installaon. Check for proper drain hose installaon. Make sure it is not
inserted more than 4.5” (114 mm). Make sure drain hose is not
sealed into drain pipe, and that there is an air gap for venlaon.
Standpipe posion. Ensure drain height is between 39” (991 mm) and 8’ (2.4 m)
above the oor.
Draining slowly. Check for pump or drain hose obstrucons.
Water pressure drop. Results in longer ll me.
Fricon or drag on drive. Check motor and bearings; check for clothes between tub and
basket.
Weak suspension. Basket should not bounce up and down more than once when
pushed.
Connued on next page . . .