Service Manual
Table Of Contents
- Service Manual - 27" Gas & Electric Stacked Laundry Center, L-95
- Table of Contents
- Section 1 - General Information
- Section 2 - Diagnostics & Troubleshooting
- Diagnostic Guide
- Diagnostic LED-Main Control
- Self Diagnostic Test Modes (Washer)
- Activating the Service Diagnostic Test Modes (Washer)
- Unsuccessful Entry
- Exiting the Service Diagnostic Test Modes (Washer)
- Customer Viewable Fault Codes (Washer)
- Fault/Error Codes Chart (Washer)
- Automatic Test Mode Chart (Washer)
- Manual Test Mode Chart (Washer)
- Washer Troubleshooting Guide
- Dryer Troubleshooting Guide
- Section 3 - Testing - Washer
- Section 4 - Testing - Dryer
- Section 5 - Component Access
- Product Specifications & Warranty Information Sources
DIAGNOSTICS & TROUBLESHOOTING
27” Stacked Laundry Center
n
2-11
- See page 2-4 to access Manual Test Mode.
Pressing the START buon will acvate/deacvate each output. When the output is acvated, the corresponding Status LEDs will
ash. IMPORTANT: Lid must be closed and locked to perform SPIN & AGITATE tests.
For Service Technician Use Only
OUTPUT STATUS LEDs
Output Details
NOTE: Outputs will me-out aer 5 minutes.
WASH
RINSE
DRAIN
SPIN
DONE
LID LOCK
Lock and unlock the lid. NOTES: When lock is enabled, the “Lid Lock” LED will turn ON. Will only lock when lid
is closed. Will only unlock when basket RPM is 0. If lid is not closed, washer will ash status LEDs on and o.
• If lid does not lock or unlock, go to TEST #7: Lid Lock, page 3-15.
COLD VALVE 1
Turns ON and turns OFF cold water valve.
• If valve does not turn on, go to TEST #2: Valves, page 3-7.
HOT VALVE 2
Turns ON and turns OFF hot water valve.
• If valve does not turn on, go to TEST #2: Valves, page 3-7.
RESERVED FOR FUTURE DEVELOPMENT 2 1
If selected, status LEDs will ash on and o.
RESERVED FOR FUTURE DEVELOPMENT 4
If selected, status LEDs will ash on and o.
RESERVED FOR FUTURE DEVELOPMENT 4 1
If selected, status LEDs will ash on and o.
RESERVED FOR FUTURE DEVELOPMENT 4 2
If selected, status LEDs will ash on and o.
DRAIN 4 2 1
Turns ON and turns OFF the drain pump.
• If pump does not turn on, go to TEST #6: Drain Pump, page 3-14.
RESERVED FOR FUTURE DEVELOPMENT 8
If selected, status LEDs will ash on and o.
8 1 On
Spins basket from 0 to 500 RPM. NOTE: Allow up to 15 seconds for shier to reposion. IMPORTANT: To acvate Low Spin,
must read “0” and lid must be closed with lid lock enabled. If lid is not closed, status LEDs will ash on and o. IMPORTANT:
Water in tub must be drained before test.
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shier & Motor), pages 3-8 & 3-10.
8 2 On
Spins basket from 0 to maximum RPM. NOTE: Allow up to 15 seconds for shier to reposion.
IMPORTANT: To acvate High Spin, RPM must read “0” and lid must be closed with lid lock enabled. If
l i d i s n o t c l o s e d , s t a t u s L E D s w i l l a s h o n a n d o . I M P O R TA N T: W a t e r i n t u b m u s t b e d r a i n e d b e f o r e t e s t .
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shier & Motor), pages 3-8 & 3-10.
8 2 1 On
Shis from idle motor to gentle CW/CCW agitaon. NOTE: Allow up to 15 seconds for shier to reposion.
IMPORTANT: To acvate Gentle Agitaon, RPM must read “0” and lid must be closed with lid lock enabled. If lid is not
closed, status LEDs will ash on and o.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shier & Motor), pages 3-8 & 3-10.
8 4 On
Shis from idle motor to gentle CW/CCW agitaon. NOTE: Allow up to 15 seconds for shier to reposion.
IMPORTANT: To acvate Gentle Agitaon, RPM must read “0” and lid must be closed with lid lock enabled. If lid is not
closed, status LEDs will ash on and o.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shier & Motor), pages 3-8 & 3-10.
= ON