Service Manual
Table Of Contents
- Smart All-In-One Washer/Dryer
- Table of Contents
- Section 1: General Information
- Washer & Dryer Safety
- Introduction
- Features
- Options
- Accessories
- Control Panel & Features
- Control Panel - Tools
- Load & Go Bulk Dispenser
- Theory of Operation - Dry Cycle
- Product Specifications
- Wiring Diagram & Model/Serial Number Location
- Model & Serial Number Nomenclature
- All-In-One Washer/Dryer Maintenance
- Cleaning the Drain Pump Filter/Draining Residual Water
- How to Manually Open a Locked Door
- Section 2: Diagnostics & Troubleshooting
- Section 3: Component Testing
- Component Testing Safety
- Wiring Diagram
- TEST #1: Appliance Control Unit (ACU) Power Check
- TEST #2: Human-Machine Interface (HMI)
- TEST #3: Motor Circuit
- TEST #4: Door Lock System
- TEST #5: Inlet Valve
- TEST #6: Pressure Switch
- TEST #7: Drain/Recirculation Pump
- TEST #8: Wash Heating Element
- TEST #9: Wash Temperature Sensor
- TEST #10a: Dispenser Sensing
- TEST #10b: Dispenser Metering Pumps
- TEST #11: Supply Connections
- TEST #12a: Dry Heating Element
- TEST #12b: Dry Temperature Sensor
- TEST #13: Dry Fan Motor
- Section 4: Component Access
- Removing the Door Assembly
- Removing the Top Panel
- Replacing the Human-Machine Interface (HMI)
- Removing the Front Panel & Bulkhead
- Removing the Rear Access Panel
- Removing the Inlet Valve Assembly
- Removing the Pressure Switch
- Removing the Metering Pumps
- Removing the Detergent Dispenser
- Removing the Dryer Heating Channel Assembly
- Removing the Condenser Duct Assembly
- Removing the RFI Filter
- Removing the Door Lock Assembly
- Removing the Appliance Control Unit (ACU)
- Removing the Motor Control Unit (MCU)
- Removing the Heater & Thermistor
- Removing the Drain & Recirculation Pumps
- Removing the Direct Drive Motor
- Removing the Tub Assembly
- Section 5: Connectivity
- Product Specifications & Warranty Information Sources
CONNECTIVITY
Whirlpool Smart All-In-One Washer & Dryer
n
5-3
Internet Connectivity Guide
Get the App and Get Connected
With your mobile device, get the app, connectivity setup instructions, terms of use, and privacy policy at:
www.whirlpool.com/connect
In Canada, visit
www.whirlpool.ca/en_CA
and click on the Whirlpool® Connected Appliances link.
IMPORTANT: Proper installaon of the appliance prior to use
is the customer responsibility. Be sure to read and follow the
Installaon Instrucons that came with the appliance.
Connecvity requires WiFi and account creaon. App
features and funconality subject to change. Data rates may
apply. If you have any problems or quesons, call Whirlpool
Corporaon Connected Appliances at 1-866-333-4591.
You Will Need:
48
Setup (cont.)
NOTE: If this is your rst Smart Appliance, you will need to download the Whirlpool
®
app and create an online user account.
If you already have the app and a user account, please skip ahead to “Register your washer/dryer in your user account.”*
From your mobile device, smartphone, or tablet, go to
www.whirlpool.com/connect and follow the instructions
to download and install the Whirlpool
®
app.
3. Download app
Registering your washer/dryer in your account is a necessary
step in order for you to take full advantage of the Smart
Features. When prompted by the app, enter the Smart Appliance
Identi cation Number (SAID) (case sensitive), which can be
found on a sticker inside the washer/dryer door.
My Smart Appliance ID# is:
NOTES:
• Once you’ve connected your washer/dryer to your home
Wi-Fi network, it will remain linked even if the power goes
out, you move the appliance, or if you put it in storage for
a while.
• If you replace your wireless router (or get a different Smart
Washer/Dryer), you will need to repeat this connectivity
setup process.
Register your washer/dryer in your
user account
4. Account setup
SET UP
Once installed, tap the Whirlpool
®
app icon to run the app.You
will be guided through the steps to set up a user account. The
app will make sure to get the necessary personal and home
information, as well as information about your energy company.
SET UP
*Subject to terms of use and privacy policy at www.whirlpool.com/connect.
n A home wireless router supporng
WiFi, 2.4Ghz with WPA2 security. If you
are unsure of the router’s capabilies,
refer to the router manufacturer’s
instrucons.
n The router to be on and have a live
internet connecon.
n The 10-character SAID code for the
appliance. The SAID code is either
printed on a label on the appliance or
can be found on the LCD screen. Refer
to “General Informaon” secon of this
manual for the locaon.
Perform the following steps to download and install the App.
Once installed, launch the app. You will be guided through the
steps to set up a user account and to connect the appliance.
If you have any problems or quesons, call Whirlpool
Corporaon Connected Appliances at 1-866-333-4591.
1. Download App
From your mobile device, smartphone, or tablet, go to
www.whirlpool.com/connect and follow the instrucons to
download and install the Whirlpool® app.
48
Setup (cont.)
NOTE: If this is your rst Smart Appliance, you will need to download the Whirlpool
®
app and create an online user account.
If you already have the app and a user account, please skip ahead to “Register your washer/dryer in your user account.”*
From your mobile device, smartphone, or tablet, go to
www.whirlpool.com/connect and follow the instructions
to download and install the Whirlpool
®
app.
3. Download app
Registering your washer/dryer in your account is a necessary
step in order for you to take full advantage of the Smart
Features. When prompted by the app, enter the Smart Appliance
Identi cation Number (SAID) (case sensitive), which can be
found on a sticker inside the washer/dryer door.
My Smart Appliance ID# is:
NOTES:
• Once you’ve connected your washer/dryer to your home
Wi-Fi network, it will remain linked even if the power goes
out, you move the appliance, or if you put it in storage for
a while.
• If you replace your wireless router (or get a different Smart
Washer/Dryer), you will need to repeat this connectivity
setup process.
Register your washer/dryer in your
user account
4. Account setup
SET UP
Once installed, tap the Whirlpool
®
app icon to run the app.You
will be guided through the steps to set up a user account. The
app will make sure to get the necessary personal and home
information, as well as information about your energy company.
SET UP
*Subject to terms of use and privacy policy at www.whirlpool.com/connect.
2. Account Setup
Once installed, tap the Whirlpool® app icon to run the app.
You will be guided through the steps to set up a user account.
The app will make sure to get the necessary personal and
home informaon, as well as informaon about your energy
company.
3. Register the washer/dryer in the user account
Registering the washer/dryer in your account is a necessary
step in order for the consumer to take full advantage of the
Smart Features. When prompted by the app, enter the Smart
Appliance Idencaon Number (SAID) (case sensive), which
can be found on a scker inside the washer/dryer door.
48
Setup (cont.)
NOTE: If this is your rst Smart Appliance, you will need to download the Whirlpool
®
app and create an online user account.
If you already have the app and a user account, please skip ahead to “Register your washer/dryer in your user account.”*
From your mobile device, smartphone, or tablet, go to
www.whirlpool.com/connect and follow the instructions
to download and install the Whirlpool
®
app.
3. Download app
Registering your washer/dryer in your account is a necessary
step in order for you to take full advantage of the Smart
Features. When prompted by the app, enter the Smart Appliance
Identi cation Number (SAID) (case sensitive), which can be
found on a sticker inside the washer/dryer door.
My Smart Appliance ID# is:
NOTES:
• Once you’ve connected your washer/dryer to your home
Wi-Fi network, it will remain linked even if the power goes
out, you move the appliance, or if you put it in storage for
a while.
• If you replace your wireless router (or get a different Smart
Washer/Dryer), you will need to repeat this connectivity
setup process.
Register your washer/dryer in your
user account
4. Account setup
SET UP
Once installed, tap the Whirlpool
®
app icon to run the app.You
will be guided through the steps to set up a user account. The
app will make sure to get the necessary personal and home
information, as well as information about your energy company.
SET UP
*Subject to terms of use and privacy policy at www.whirlpool.com/connect.
Smart Appliance ID# is:
__________________________________________________
NOTES:
• Once the washer/dryer is connected to the consumer’s
home WiFi network, it will remain linked even if the power
goes out, the appliance is moved, or if it is put in storage
for a while.
• If the consumer replaces their wireless router (or get a
dierent Smart Washer/Dryer), you will need to repeat this
connecvity setup process.