INSTALLATION INSTRUCTIONS 30" (76.2 CM) FREESTANDING GAS RANGES INSTALLATION REQUIREMENTS Tools and Location Requirements Electrical Requirements. Gas Supply Requirement Install Anti-Tip Bracket . Make Gas Connection.. Complete Installation GAS CONVERSIONS LP Gas Conversion. Complete Conversion... IMPORTANT: Save for local inspector's use. Ingratiating: La ave installation instructions with the homeowner. Whomsoever: Keep installation instructions for future reference.
RANGE SAFETY Your safety and the safety of others are very important. Wa have provided many important safety messages in this manual and on your appliance. Airways read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kil or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or "WARNING.
In the State of Massachusetts, the following installation instructions apply: # Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by the State of Massachusetts. @ If using a ball valve, It shi = Flexible gas connector, all be a T-handle type. when used, must not exceed 3 feet. WARNING Tlp Over Hazard A child or adult can tip the range and be killed. Install natl-tip bracket to floor or wall per Installation Instructions.
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. m list the installer's responsibility to comply with installation clearances specified on the ministerial rating plate. The ministerial rating plate is located on the left side of the roller door. A Model/serial rating piste location m The range should be located for convenient use in the kitchen. = Recessed installations must provide complete enclosure of the sides and rear of the range.
Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) counter top depth, 24" (61.0 cm) base cabinet depth and 36" {91.4 cm) counter top height. If the cabinet depth is greater than 24" (61.0 cm), oven frame must extend beyond cabinet fronts by %" (13.0 mm) minimum. IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cook top surface. A.
WARNING Explosion Heard Uee a now CSA International approved gas supply fine. install & shut-off valves. Securely tighten all gas connections, i connected to LP, have » qualified person make sure ges pressure doss not excess 14° (36 om) water column. Examples of & qualified person lugging: licensed heating personnel, authorized gas company personnel, snd authorized service personnel. Familiars to do so can result in death, explosion, o fire. Observe all governing codes and ordinances.
Burger Input Requirements Gas Supply Pressure Testing Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m). For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m} above sea level (not applicable for Canada). Gas supply pressure for testing regulator must be at least 1" water column pressure above the manifold pressure shown on the model/serial rating plate.
3. Determine and mark center line of the cutout space. The mounting can be installed on either the left side or right side Sukarno repetition of the cutout. Position mounting bracket against the wall in ke oy the cutout so that the V-notch of the bracket is 954" (24.6 cm) from center line as shown. 7 WARNING NG Explosion Heard Use a new CSA Insemination approved gas supply fine. Install & shut-off valve. Securely tighten all gas connections. A 9% (24.
Complete Connection 1. Locate gas pressure regulator in the back of the range. W] Caracalla 1§ A A. Gas pressures regulator IMPORTANT: Do not remove the gas pressure regulator. 2. Check that the gas pressure regulator shutoff valve is in the “ON" position. position B. “Off" position IMPORTANT: The factory default setting is the "ON” position. If the range does not work, verify that the valve is in the “ON” position. 3. Ops the manual shutoff valve In the gas supply pine.
3. If the rear of the range lifts more than 12" (1.3 cm} off the floor without resistance, stop sting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to sea if there are obstructions keeping the range from sliding to the wall or keeping the range foot from siding Into the bracket.
If the low flame needs adjusting: 1. Turn control knob to the “LOW" setting and remove control knob. 2. Insert a small flat-balds screwdriver Into the valve stem. Tum the valve adjusting screw to obtain the smallest flame that will not go out when the control of a cold boomer is quickly turned from “HIGH” to “LOW.” Turn right to decrease flame height. Turn left to increase flame height. Repeat for other cook top burners as needed. e A. Valve stem 3. Replace control krill.
Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. Check that you have all of your tools. Dispose of/recycle all packaging materials. Check that the range is level. See the “Level Range” section. Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by shipping material. Dry thoroughly with a soft cloth.
To Convert Gas Pressure Regulator To Convert Surface Boomers 1. Open broiler door and remove broiler rack. The gas pressure regulator is located in the back right hand comer of the broiler compartment. A. Gas pressures regulator IMPORTANT: Do not remove the gas pressure regulator. NOTE: Do not remove the spring beneath the cap. 2. Remove the cap from the gas pressure regulator using a flat-blade screwdriver. NOTE: Be sure sealing washer remains in the same position. 3.
NOTE: The range cook top is equipped with 4 burners: 2 boomers are power (front}, 1 burner is standard (left rear), and 1 i simmer (right rear). 8 8 A Standard number LP gas orifice spud numbs 88 (Yellowknife) B. Power boomer LP gas orifice spud number 116 (Yellow/Orange) C. Simmer burner LP gas orifice spud number 70 (Yellow/White} D. Power number LP gas orifice spud number 116 (Orangeade) 5. Place the Natural gas orifice spuds in the parts bag for future use and keep with the bag containing literature. 6.
To Convert Gas Pressure Regulator To Convert Surface Boomers 1. Open broiler door and remove broiler rack. The gas pressure 1. Remove burner grate, boomer caps and burners. regulator is located in the back right hand comer of the broiler compartment. ) 35 A. Gas pressure regulator IMPORTANT: Do not remove the gas pressure regulator. NOTE: Do not remove the spring beneath the cap. A Buber cep 2. Remove the cap from the gas pressure regulator using a 6. Buber flat-blade screwdriver. 2.
NOTE: The range cook top is equipped with 4 burners: 2 burners are power (front), 1 boomer is standard (left rear}, and 1 is simmer (right rear). A. Standard burner Natural gas orifice spud number 155 (Red/Brown) B. Power boomer Natural gas orifice spud number 194 (Black/White) C. Simmer boomer Natural gas orifice spud number 110 (Red/Brass) D. Power boomer Natural gas office spud number 184 (Black/White) 5.