Owner's Manual
Table Of Contents
- Washer Safety
- Washer Safety
- Internet Connectivity Guide
- Choosing the Right Detergent
- Choosing the Right Detergent
- Adding Laundry Products
- Washer Maintenance and Care
- Cleaning the Washer Location
- Water Inlet Hoses
- Washer Care
- Clean Washer Cycle Reminder
- Removing the Dispenser
- Cleaning Load & Go™ Containers (on some models)
- Nonuse and Vacation Care
- Winter Storage Care
- Transporting Your Washer
- Reinstalling/Using Washer Again
- Cleaning the Drain Pump/Draining Residual Water (on some models)
- Additional Cleaning
- Installation Instructions
- Requirements
- Tools and Parts
- Location Requirements
- Drain System
- Electrical Requirements
- Installation
- Unpacking
- Connect Drain Hose
- Connect Inlet Hoses
- Level Washer
- Complete Installation Checklist
- Sécurité de la laveuse
- Sécurité de la laveuse
- Guide de connexion Internet
- Choix du détergent approprié
- Choix du Détergent Approprié
- Ajouter les produits de lessive
- Entretien et réparation de la laveuse
- Nettoyage de l'emplacement de la laveuse
- Tuyaux d’arrivée d’eau
- Entretien de la laveuse
- Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)
- Retrait du distributeur
- Récipients Load & Go™ (sur certains modèles)
- Non utilisation et entretien avant les vacances
- Entretien pour entreposage hivernal
- Transport de la laveuse
- Réinstallation/réutilisation de la laveuse
- Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles)
- Nettoyage supplémentaire
- Instructions d’installation
- Spécifications
- Outils et pièces
- Exigences d’emplacement (laveuse)
- Système de vidange
- Spécifications électriques
- L’installation
- Déballage
- Raccordement du tuyau de vidange
- Raccordement des tuyaux d’alimentation
- Établissement de l’aplomb de la laveuse
- Liste de vérification pour installation terminée
8
Transporting Your Washer
1. Shut off both water faucets. Disconnect and drain water inlet
hoses.
2. If washer will be moved during freezing weather, follow
“Winter Storage Care” directions before moving.
3. Disconnect drain hose from drain system and from back of
washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside drum.
6. Bundle power cord with a rubber band or cable tie to keep it
from hanging to the ground.
IMPORTANT: Call for service to install new transport bolts. Do not
reuse transport bolts. Washer must be transported in the upright
position. To avoid structural damage to your washer, it must be
properly set up for relocation by a certified technician.
Reinstalling/Using Washer Again
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
To reinstall washer after nonuse, vacation, winter
storage, or moving:
1. Refer to Installation Instructions to locate, level, and connect
washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses.
2. Reconnect water-inlet hoses.
3. Turn on both water faucets.
4. Plug into a grounded 3-prong outlet or reconnect power.
5. Run washer through Heavy Duty/Power Wash cycle to clean
washer and remove antifreeze, if used. Use only HE
detergent. Use half the manufacturer’s recommended amount
for a medium-size load.
Cleaning the Drain Pump/Draining
Residual Water (on some models)
IMPORTANT: Make sure the washer is off before cleaning the
drain pump filter.
NOTE: Perform the following procedure occasionally.
1. Open the dispenser drawer by pulling on the handle at the
base of the washer. This will reveal the drain pump filter.
Remove the drawer by releasing the tab on each side.
With your finger, push down on tab on right side of drawer,
and up on tab on left side of drawer.
2. Place a broad, flat container beneath the drain pump filter to
collect the drain water. Release the black hose from the hose
clip, remove the plug, and drain the hose into the container.
Empty the container. Repeat this procedure if necessary until
all the water has drained. Make sure that the black hose is
completely dry, replace the plug, and secure the hose in the
clip.
NOTE: If water does not drain well, push in hose slightly to
remove any possible kinks.
3. Lay a cotton cloth beneath the drain pump filter to absorb any
water still in it. Then remove the drain pump filter by turning it
counterclockwise.