Installation Guide
Table Of Contents
- WASHER SAFETY
- Washer Safety
- Internet Connectivity Guide
- CHOOSING THE RIGHT DETERGENT
- Choosing the Right Detergent
- Adding Laundry Products
- WASHER MAINTENANCE AND CARE
- Cleaning the Washer Location
- Water Inlet Hoses
- Washer Care
- Clean Washer Cycle Reminder
- Removing the Dispenser
- Cleaning Load & Go™ Containers (on some models)
- Nonuse and Vacation Care
- Winter Storage Care
- Transporting Your Washer
- Reinstalling/Using Washer Again
- Cleaning the Drain Pump/Draining Residual Water (on some models)
- Additional Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Drain System
- Electrical Requirements
- INSTALLATION
- Unpacking
- Connect Drain Hose
- Connect Inlet Hoses
- Level WasherComplete Installation Checklist
- Complete Installation Checklist
- SECURITE DE LA LAVEUSE
- Sécurité de la laveuse
- Guide de connexion Internet
- CHOIX DU DETERGENT APPROPRIE
- Choix du détergent approprié
- Ajouter les produits de lessive
- ENTRETIEN ET REPARATION DE LA LAVEUSE
- Nettoyage de l'emplacement de la laveuse
- Tuyaux d’arrivée d’eau
- Entretien de la laveuse
- Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)
- Retrait du distributeur
- Récipients Load & Go (sur certains modèles)
- Non utilisation et entretien avant les vacances
- Entretien pour entreposage hivernalTransport de la laveuse
- Transport de la laveuse
- Réinstallation/réutilisation de la laveuse
- Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles)
- Nettoyage supplémentaire
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pièces
- Exigences d’emplacement (laveuse)
- Système de vidange
- Spécifications électriques
- INSTALLATION
- Déballage
- Raccordement du tuyau de vidange
- Raccordement des tuyaux d’alimentation
- Établissement de l’aplomb de la laveuseListe de vérification pour installation terminée
- Liste de vérification pour installation terminée
- Untitled
14
5. Remove drain hose form (floor drain
installations only)
For floor drain installations, you will need to remove the drain
hose form from the end of the drain hose. You may need
additional parts with separate directions; refer to the Quick
Start Guide.
6. Place drain hose in standpipe
Place hose into standpipe (shown in picture) or over side of
laundry tub.
IMPORTANT: 4.5" (114 mm) of drain hose should be inside
standpipe; do not force excess hose into standpipe or lay on
bottom of laundry tub. Drain hose form must be used.
Connect Inlet Hoses
IMPORTANT: To avoid leaks, check that your water inlet hoses
have flat washers at both ends. Washer must be connected to
water faucets with new inlet hoses with flat washers (not
provided). Do not use old hoses. Do not use hoses without
washers.
7. Insert new flat washers
8. Connect inlet hoses to water faucets
IMPORTANT: Do not overtighten or use tape or sealants on
valve when attaching to faucets or washer. Damage can
result.
Attach the hose labeled hot to hot water faucet. Screw on
coupling by hand until it is seated on washer. Use adjustable
pliers to tighten couplings an additional two-thirds turn.
Repeat this step with the hose labeled cold for the cold water
faucet. Both hoses must be connected for washer to work
properly.
HELPFUL TIP: Make note of which hose is connected to hot
water to help in attaching hoses to washer correctly. In most
standard configurations, hoses will cross over each other
when attached correctly.
9. Clear water lines
Run water for a few seconds through hoses into a laundry
tub, drainpipe, or bucket to prevent clogs. Water should run
until clear.