Owner's Manual
Table Of Contents
- Washer Safety
- Washer Safety
- Internet Connectivity Guide
- Choosing the Right Detergent
- Choosing the Right Detergent
- Adding Laundry Products
- Washer Maintenance and Care
- Cleaning the Washer Location
- Water Inlet Hoses
- Washer Care
- Clean Washer Cycle Reminder
- Removing the Dispenser
- Cleaning Load & Go™ Containers (on some models)
- Nonuse and Vacation Care
- Winter Storage Care
- Transporting Your Washer
- Reinstalling/Using Washer Again
- Cleaning the Drain Pump/Draining Residual Water (on some models)
- Additional Cleaning
- Installation Instructions
- Requirements
- Tools and Parts
- Location Requirements
- Drain System
- Electrical Requirements
- Installation
- Unpacking
- Connect Drain Hose
- Connect Inlet Hoses
- Level Washer
- Complete Installation Checklist
- Sécurité de la laveuse
- Sécurité de la laveuse
- Guide de connexion Internet
- Choix du détergent approprié
- Choix du Détergent Approprié
- Ajouter les produits de lessive
- Entretien et réparation de la laveuse
- Nettoyage de l'emplacement de la laveuse
- Tuyaux d’arrivée d’eau
- Entretien de la laveuse
- Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)
- Retrait du distributeur
- Récipients Load & Go™ (sur certains modèles)
- Non utilisation et entretien avant les vacances
- Entretien pour entreposage hivernal
- Transport de la laveuse
- Réinstallation/réutilisation de la laveuse
- Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles)
- Nettoyage supplémentaire
- Instructions d’installation
- Spécifications
- Outils et pièces
- Exigences d’emplacement (laveuse)
- Système de vidange
- Spécifications électriques
- L’installation
- Déballage
- Raccordement du tuyau de vidange
- Raccordement des tuyaux d’alimentation
- Établissement de l’aplomb de la laveuse
- Liste de vérification pour installation terminée
13
2. Locate transport bolts
Locate four transport bolts on rear of washer.
3. Remove transport bolts from washer
Loosen bolts with a 5/8" (16 mm) wrench. Slide each bolt and
spacer to center of hole. Pull bolts and plastic spacers from
back of washer. Discard bolts and spacers.
IMPORTANT: Do not plug washer in until installation has
been completed.
Connect Drain Hose
4. Attach drain hose to drain port
If clamp is not already in place on elbow end of drain hose,
squeeze clamp with pliers and slide it over end of hose,
centering it between the ribs, as shown. Squeeze clamp with
pliers and slide elbow end of drain hose onto drain port and
secure with clamp.
For a laundry tub or standpipe drain, go to step 6.
For a floor drain, remove the preinstalled drain hose form as
shown in step 5. You may need additional parts with separate
directions. See “Alternate Parts.”
It is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of or leaking from the
plumbing/drain.
5. Remove drain hose form (floor drain
installations only)
For floor drain installations, you will need to remove the drain
hose form from the end of the drain hose. You may need
additional parts with separate directions; refer to the Quick
Start Guide.