Owner's Manual
Table Of Contents
- Washer Safety
- Washer Safety
- Internet Connectivity Guide
- Choosing the Right Detergent
- Choosing the Right Detergent
- Adding Laundry Products
- Washer Maintenance and Care
- Cleaning the Washer Location
- Water Inlet Hoses
- Washer Care
- Clean Washer Cycle Reminder
- Removing the Dispenser
- Cleaning Load & Go™ Containers (on some models)
- Nonuse and Vacation Care
- Winter Storage Care
- Transporting Your Washer
- Reinstalling/Using Washer Again
- Cleaning the Drain Pump/Draining Residual Water (on some models)
- Additional Cleaning
- Installation Instructions
- Requirements
- Tools and Parts
- Location Requirements
- Drain System
- Electrical Requirements
- Installation
- Unpacking
- Connect Drain Hose
- Connect Inlet Hoses
- Level Washer
- Complete Installation Checklist
- Sécurité de la laveuse
- Sécurité de la laveuse
- Guide de connexion Internet
- Choix du détergent approprié
- Choix du Détergent Approprié
- Ajouter les produits de lessive
- Entretien et réparation de la laveuse
- Nettoyage de l'emplacement de la laveuse
- Tuyaux d’arrivée d’eau
- Entretien de la laveuse
- Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)
- Retrait du distributeur
- Récipients Load & Go™ (sur certains modèles)
- Non utilisation et entretien avant les vacances
- Entretien pour entreposage hivernal
- Transport de la laveuse
- Réinstallation/réutilisation de la laveuse
- Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles)
- Nettoyage supplémentaire
- Instructions d’installation
- Spécifications
- Outils et pièces
- Exigences d’emplacement (laveuse)
- Système de vidange
- Spécifications électriques
- L’installation
- Déballage
- Raccordement du tuyau de vidange
- Raccordement des tuyaux d’alimentation
- Établissement de l’aplomb de la laveuse
- Liste de vérification pour installation terminée
14
6. Place drain hose in standpipe
Place hose into standpipe (shown in picture) or over side of
laundry tub.
IMPORTANT: 4.5" (114 mm) of drain hose should be inside
standpipe; do not force excess hose into standpipe or lay on
bottom of laundry tub. Drain hose form must be used.
Connect Inlet Hoses
IMPORTANT: To avoid leaks, check that your water inlet hoses
have flat washers at both ends. Washer must be connected to
water faucets with new inlet hoses with flat washers (not
provided). Do not use old hoses. Do not use hoses without
washers.
7. Insert new flat washers
8. Connect inlet hoses to water faucets
IMPORTANT: Do not overtighten or use tape or sealants on
valve when attaching to faucets or washer. Damage can
result.
Attach the hose labeled hot to hot water faucet. Screw on
coupling by hand until it is seated on washer. Use adjustable
pliers to tighten couplings an additional two-thirds turn.
Repeat this step with the hose labeled cold for the cold water
faucet. Both hoses must be connected for washer to work
properly.
HELPFUL TIP: Make note of which hose is connected to hot
water to help in attaching hoses to washer correctly. In most
standard configurations, hoses will cross over each other
when attached correctly.
9. Clear water lines
Run water for a few seconds through hoses into a laundry
tub, drainpipe, or bucket to prevent clogs. Water should run
until clear.
10. Connect inlet hoses to washer
IMPORTANT: To reduce risk of hose failure, replace the
hoses every 5 years. Record hose installation or replacement
dates for future reference.
n Do not overtighten hose or use tape or sealants on the
valve. Damage to the valves can result.
n Periodically inspect and replace hoses if bulges, kinks,
cuts, wear, or leaks are found.
Attach hot water hose to hot water inlet valve. Screw
coupling by hand until it is snug. Use adjustable pliers to
tighten couplings an additional two-thirds turn. Repeat with
cold water inlet valve.
11. Check for leaks
Slowly turn on water faucets to check for leaks. A small
amount of water may enter washer. It will drain later.