Owner's Manual
Table Of Contents
- WASHER SAFETY
- Washer Safety
- Internet Connectivity Guide
- CHOOSING THE RIGHT DETERGENT
- Choosing the Right Detergent
- Adding Laundry Products
- WASHER MAINTENANCE AND CARE
- Cleaning the Washer Location
- Water Inlet Hoses
- Washer Care
- Clean Washer Cycle Reminder
- Removing the Dispenser
- Cleaning Load & Go™ Containers (on some models)
- Nonuse and Vacation Care
- Winter Storage Care
- Transporting Your Washer
- Reinstalling/Using Washer Again
- Cleaning the Drain Pump/Draining Residual Water (on some models)
- Additional Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Drain System
- Electrical Requirements
- INSTALLATION
- Unpacking
- Connect Drain Hose
- Connect Inlet Hoses
- Level WasherComplete Installation Checklist
- Complete Installation Checklist
- SECURITE DE LA LAVEUSE
- Sécurité de la laveuse
- Guide de connexion Internet
- CHOIX DU DETERGENT APPROPRIE
- Choix du détergent approprié
- Ajouter les produits de lessive
- ENTRETIEN ET REPARATION DE LA LAVEUSE
- Nettoyage de l'emplacement de la laveuse
- Tuyaux d’arrivée d’eau
- Entretien de la laveuse
- Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)
- Retrait du distributeur
- Récipients Load & Go (sur certains modèles)
- Non utilisation et entretien avant les vacances
- Entretien pour entreposage hivernalTransport de la laveuse
- Transport de la laveuse
- Réinstallation/réutilisation de la laveuse
- Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles)
- Nettoyage supplémentaire
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pièces
- Exigences d’emplacement (laveuse)
- Système de vidange
- Spécifications électriques
- INSTALLATION
- Déballage
- Raccordement du tuyau de vidange
- Raccordement des tuyaux d’alimentation
- Établissement de l’aplomb de la laveuseListe de vérification pour installation terminée
- Liste de vérification pour installation terminée
- Untitled
15
10. Connect inlet hoses to washer
IMPORTANT: To reduce risk of hose failure, replace the
hoses every 5 years. Record hose installation or replacement
dates for future reference.
� Do not overtighten hose or use tape or sealants on the
valve. Damage to the valves can result.
� Periodically inspect and replace hoses if bulges, kinks,
cuts, wear, or leaks are found.
Attach hot water hose to hot water inlet valve. Screw
coupling by hand until it is snug. Use adjustable pliers to
tighten couplings an additional two-thirds turn. Repeat with
cold water inlet valve.
11. Check for leaks
Slowly turn on water faucets to check for leaks. A small
amount of water may enter washer. It will drain later.
12. Secure drain hose
Secure drain hose to laundry tub leg, drain standpipe, or inlet
hoses for wall standpipe with cable tie or beaded tie strap.
It is the responsibility of the installer to install and secure the
drain hose in to the provided plumbing/drain in a manner that
will avoid the drain hose coming out of or leaking from the
plumbing/drain.
Level Washer
IMPORTANT: Leveling your washer properly reduces excess
noise and vibration.
13. Check levelness of washer
Remove cardboard from beneath washer. Place a level on
top edges of washer, checking each side and front. If not
level, tip washer and adjust feet up or down as shown in
steps 15 and 16, repeating as necessary.
14. Rock washer to test foot contact
Grip washer from top and rock back and forth, making sure
all four feet are firmly on floor. Repeat, rocking washer from
side to side. If washer rocks, go to step 15 and adjust leveling
feet. If all four feet are in firm contact with floor, go to step 16.