Installation guide
INSTALL
LEVELING
LEGS
VENTING
A
WARNING
VENTING
REQUIREMENTS
Excessive
Weight
Hazard
A
WARNING
Use
two
or
more
people
to
move
and
install
dryer.
‘S
Failure
to
do
so
can
result
in
back
or
other
injury.
4
6,
é
(4
.
Prepare
dryer
for
leveling
legs
Fire
Hazard
Use
a
heavy
metal
vent.
Do
not
use
a
plastic
vent.
Do
not
use
a
metal
foil
vent.
Failure
to
follow
these
instructions
can
result
in
death
or
fire.
WARNING:
To
reduce
the
risk
of
fire,
this
dryer
MUST
BE
EXHAUSTED
OUTDOORS.
IMPORTANT:
Observe
all
governing
codes
and
ordinances.
Dryer
exhaust
must
not
be
connected
into
any gas
vent,
chimney,
wall,
ceiling,
attic,
crawlspace,
or
a
concealed
space
of
a
building.
Only
rigid
or
flexible
metal
vent
shail
be
used
for
exhausting.
To
avoid
damaging
floor,
use
a
large
flat
piece
of
cardboard
from
dryer
carton;
place
under
entire
dryer.
Firmly
grasp
dryer
body
(not
console
panel)
and
gently
lay
dryer
down
on
cardboard.
IMPORTANT:
If
laying
dryer
on
its
back,
use
the
cardboard
corner
posts
the
dryer
was
packed
with
to
avoid
damaging
the
back
of
the
dryer.
Lay
the
dryer
on
its
side
if
you
do
not
have
the
cardboard
corner
posts
the
dryer
was
packed
with.
4"
(102
mm)
(2.
Screw
in
leveling
legs
4"
(102
mm)
heavy
metal
exhaust
vent
@
Only
a
4"
(102
mm)
heavy
metal
exhaust
vent
and
clamps
may
be
used.
@
Do
not
use
plastic
or
metal
foil
vent.
Rigid
metal
vent:
@
Recommended
for
best
drying
performance
and
to
avoid
crushing
and
kinking.
Flexible
metal
vent:
(Acceptable
only
if
accessible
to
clean)
@
Must
be
fully
extended
and
supported
in
final
dryer
location.
:
:
:
@
Remove
excess
to
avoid
sagging
and
kinking
that
may
Examine
leveling
legs.
Screw
legs
into
leg
holes
by
hand,
result
in
reduced
airflow
and
poor
performance.
use
a
wrench
if
necessary,
to
finish
turning
legs
until
they
; ;
.
begin
to
touch
the
base.
@
Do
not
install
in
enclosed
wails,
ceilings,
or
floors.
Now
stand
the
dryer
on
its
legs.
Slide
the
dryer
until
it
is
&
The
total
length
should
not
exceed
7
°/.
ft.
(2.4
m).
close
to
its
final
location.
Leave
enough
room
for
electrical
connection
and
to
connect
the
exhaust
vent.
NOTE:
If
using
an
existing
vent
system,
clean
lint
from
entire
length
of
the
system
and
make
sure
exhaust
hood
is
not
plugged
with
lint.
Replace
plastic
or
metal
foil
vents
with
rigid
metal
or
flexible
metal
vents.
Review
Vent
System
Chart
and
if
necessary,
modify
existing
vent
system
to
achieve
best
drying
performance.