Owners Manual
Table Of Contents
- RANGE SAFETY
- Range Safety
- RANGE MAINTENANCE AND CARE
- Self-Cleaning Cycle
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements (for Dual Fuel models) - U.S.A. Only
- Electrical Requirements (for Dual Fuel models) - Canada Only
- Electrical Requirements (for Gas models)
- Gas Supply Requirements
- INSTALLATION
- Unpack Range
- Install Anti-Tip Bracket
- Make Gas Connection
- Verify Anti-Tip Bracket Is Installed and Engaged
- Level Range
- Electronic Ignition System
- Complete Installation
- Remove Oven Doors
- Adjust Leveling Legs
- GAS CONVERSIONS
- Propane Gas Conversion
- Natural Gas Conversions
- Moving the Range
- SECURITE DE LA CUISINIERE
- Sécurité de la cuisinière
- ENTRETIEN ET REPARATION DE LA CUISINIERE
- Programme d’autonettoyage (sur certains modèles)
- Nettoyage général
- INSTRUCTIONS D'INSTALLATION
- EXIGENCE
- Tools and Parts
- Exigences d’emplacement
- Spécifications électriques (Pour les modèles à bi-combustible) - Canada seulement
- Spécifications électriques (pour cuisinières à gaz)
- Spécifications de l’alimentation en gaz
- INSTALLATION
- Déballage de la cuisinière
- Installation de la bride antibasculement
- Raccordement au gaz
- Vérifier que la bride antibasculement est bien installée et engagée
- Réglage de l’aplomb de la cuisinière
- Système d’allumage électronique
- Achever l’installation
- Enlever la/les portes du four
- Réglage des pieds de nivellement
- CONVERSIONS POUR CHANGEMENT DE GAZ
- Propane Gas Conversion
- Natural Gas Conversion
- Déplacement de la cuisinière
23
To Convert Oven Broil Burner (Propane to Natural
gas)
1. Remove broil burner screw and set aside.
2. Remove the broil burner from the broil burner orifice hood.
The broil burner will hang in the back of the oven while
changing the orifice hood.
A. Broil burner screw
B. Broil burner orifice hood
3. Turn the green Number 0.037 Propane gas broil burner orifice
hood counterclockwise to remove.
A. Number 0.037 Propane gas broil burner
orifice hood
4. Install the Number 0.054 Natural gas broil burner orifice hood,
turning it clockwise 4 or 5 turns. Do not overtighten.
A. Number 0.054 Natural gas broil burner orifice
hood
5. Place the broil burner on the broil burner orifice hood. Insert
the broil burner locator pin in the hole in the oven back.
6. Position the broil burner against the roof of the oven cavity
and attach with screw.
A. Broil burner orifice hood
B. Broil burner
To Convert Surface Burners (Propane Gas to
Natural Gas)
1. Remove burner cap.
2. Remove the burner base.
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter electrode
E. Gas tube opening
3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and remove
by turning it counterclockwise and lifting out. Set gas orifice
spud aside.
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws