BUILT-IN OVEN SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol, This symbol alerts you to potential hazards that can kill or hurt you and others.
m Oven support surface must be solid, level and flush with bottom of cabinet cutout. m Floor must be able fo support a single vane weight of 128 lbs (59 kg) for 27" (68.6 cm) models or 154 Ibs (70 kg) for 30” Cabinet Dimensions Single Ovens Single Oven Under counter {without cook top installed above} (76.2 cm) models Floor must be able to support a double oven weight of ¥ 251 Ibs {114 kg) for 27" {88.6 cm) models or 288 ibs (131 kg) x for 30” {76.
Product Dimensions Double Ovens Cabinet Dimensions Double Ovens r A 27° (68,6 om) models A 51%" (130.0 omy max. overall height B. 25745" (64.8 cry max. recessed width C4895" (124.0 cm recessed height {2.2354 (59.1 cm max. recessed depth E. 27" (68.6 cmj overall width F 12" @0.s en farm back of control panel to start of strain relief G. 66" (167.8 cmy flexible conduit length 30" (76.2 om) models AST" (130.0 cm) max. overs) height B. 28%" (72.4 cr) max. recessed width ©. 48 45s" (124.0 cm} recessed height {2.
If codes armpit and a separate ground wire is used, if is recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local codes. Check with a qualified electrical installer if you are not sure the overt is properly grounded. This oven must be connected to a grounded metal, permanent wiring system.
INSTALLATION INSTRUCTIONS e Suit-In Oven 1. Decide on the final location for the oven. Avoid drilling ar cutting info house wiring during installation. PLL Excessive Weight Hazard Use two or more people to move and install even, Failure to do so can result in back or other injury. 2. To avoid floor damage, set the oven onto cardboard prior to installation. Do not use handle or any portion of the front frame for lifting 3. Remove the shipping materials and tape from the oven.
Cretan Doors} IMPORTANT: Do not replace the oven door(s) until after the oven has been installed into the cabinet. 1. Using two hands, grasp side ages of door at the midpoint. Face the oven cavity. 2. Locate the slots on each side of the oven cavity for the door hinge locks. A Slot in the oven cavity for door hinge lock angle, align door hinges with slots in the lower front of the oven cavity. Slowly insert door, making sure you maintain the 45° angle.
Cutout Height is between 26'%" (68.4 cm) and 27%" {70.3 cm} 1. Using 2 or more people, place the oven on its back on a 1. covered surface. Cutout Height is between 2814" (72.8 cm) and 29746" {74.8 cm} Using 2 or more people, place the oven on its back ona covered surface. 2. Remove the foot from the right front spacer by removing the 2 #8-18 x 3%" screw, NOTE: Da not remove the spacer. Remove the foot from the right front spacer by removing the #8-18 x 36" screw. NOTE: Da nat remove the spacer. A Spacer 8.
8. Using 2 or more people, place the overt in its upright position. 7. Go to the “Make Electrical Carnation” section. Double Ovens The positioning of the oven feet allow a double oven to be installed in a cutout height between 48%" {124.1 crm) and 52%" {132.6 mommy. Refer to the following instructions to position the feet for the size of your cabinet cutout. Cutout height is between 487" (124.1 cm) and 5076" {128.1 cm) The oven feel do not need to be installed, The oven is configured correctly as received.
8. Using 2 or more people, place the overt in its upright position. 4. Install a front foot on the left front using a #8-18 x %" screw. 7 NOTE: Position the foot so the long side of the foot is facing toward the top of the oven. J A. Front foot 7. Go to the “Make Electrical Connection” section, Ban TF oe Cutout Height is between 51%" (130.0 cm) and 52%¢" 8. In the same manner, install a front foot on the right front of the {132.6 cm) oven, 1. Using 2 or more people, place the oven on its back on a 8.
S08 Cn For Double Ovens For Single Ovens WARNING 2% Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge solid copper wire. Electrically ground oven. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 12 gauge solid copper wire. Electrically ground oven. Failure to follow these instructions can result in death, fire, or electrical shock.
3-Wire Cable from Home Power Supply U.S. Only IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection. A. Cable from home power supply F. 4-quite flexible condition from B. Junction box oven ©. Black wires G. Fed wires D. White wires HR. UL listed wire connectors £. Green for bare} ground wire J. UL sifted or CSA approved {iron oven conduit connector 1. Connect the 2 black wires (C) together using a UL listed wire corrector. 2.
8. For models KEBK171B, KEBK101B, KEBK276B, KEBK206B, KEBS179B, KEBS109B, KEBS277B, KEBS279B, KEBS207B, or KEBS2098B, see the following instructions. For all other models, the black front trims can be ordered as an accessory. Please reference the “Assistance or Service” section of the Use and Care Guide or contact the dealer from worn you purchased your built-in oven to order part nursers: W10327368 and W 10327369 for double ovens. W10827380 and W10327381 for single ovens.
{only SAE WRT On single and double oven medals installed above a warming drawer, a warming drawer deflector kit must be installed. See the “Tools and Parts” section for information on ordering NOTE: Warming drawer deflector is not needed if feet are installed in the tall position and bottom vent trim has been installed. Parts Supplied in Deflector Kit chess A goes ~ A Philips head screws (4) only 2 screws for 27" (88.6 cm size B. Warming drawer deflector (1) Install Deflector Kit 1.
SÉCURITÉ DU FOUR ENCASTRE Votre sécurité et celle des autres est trais importante. Nous donnas de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer.
EXIGENCES D'INSTALLATION Cuivrage sapiences Rassembler les outils et composants nécessaires avant d'entreprendre 'installation. Lire et observer les instructions fournies avec chacun des outils de la liste ci-dessous.
Dimensions du produit Fours simples Modales de 27° (68,6 cm) A. Hauteur hors-tout 28%" (72,8 cm) max. 8 Largeur encastrement 25 Jo’ 64,6 om) max, ©. Hauteur d’encastrement 26%" (67.9 emy D. Profondeur d'encastrement 23%" (59.1 em) max E. Largeur hors-tout 27° (68,6 cm) F 12° (30,5 cm) de Pariée du tables 06 commande jusqu's l'extrémité avant du serre-câble 4.48" (121,9 om) de longueur du conduit flexible Modales de 30° (76,2 om) A. Hauteur hors-tout 28%" (72,8 om) max.
Fours simples installés dans un placard Modelés de 27" (63,6 cm) A. Marger du placard 277(68,6 cin} min B. 1° (2,6 am entre Je sommet de l’ouverture découpée st la bas de la porte du placard supérieur C. 42" (81,3 cm) entre fe bas de Fauverture découpée et fe sol 0. Largeur de Pauvertire découpe 281 (64,8 crm) E114 (3.8 om) min. entre Ja bas dle {'ouverture découpés et le sororat de fa porte du placard F. Hauteur de ouverture découpe recommandée 28° (71,2 co) G.
Dimensions du placard Fours doubles Fours doubles installés dans un placard Modelés de 27" (68,6 om) A Largeur du placard 277 (68,6 emf min. B. 1" {2,5 cm) entre Ja sommet de Pouvertire découpée et Je bas de fa porte du placard supérieur C. 143%" (37,5 cm) entre fa bas da Fouwverturs coupecoupe et fe sof ast la distance recommandée. 4-148" cm) entre fe bas de {'ouverture découpée ef le sof ast une distance acceptable, 0.
mu Installateur doit fournir un connecteur de conduit {homologation UL ou CBA} m Si le domicile est équipé d'un câblage en aluminium, suivre les instructions suivantes : 1. Connecter une section de câble en cuivre massif aux extrémités des conducteurs souples. 2. Connecter le câblage en aluminium a la section ajoutée de câblage en cuivre en utilisant des connecteurs et/ou des outils spécialement fongus et homologués UL pour fixer le cuivre & aluminium.
hes bes Fêla Ae HAF cotre) clu four IMPORTANT : Retirer {a porte au four avec les deux mains, Pour les fours doubles, répéter le procédé pour chaque porte. 1. Avant de retirer la porte du four, préparer une surface sur laquelle on pourra la poser, Cette surface doit être plate et recouverte d'une couverture douce. On peut aussi utiliser les cornières de 'emballage. 2. Ouvrir la porte du four. 3.
8. Ferrer la porte du four. 7. Une fois les charnières correctement installées et la porte formée, il doit y avoir un espace égal entre la porte et le tableau de commande.
4. Laide d'au moins deux personnes, placer le four en position 8. Faire pivoter le pied 4 80° de faon a ce gue le coté court du verticale. pied soit orienté vers le sommet du four, 4. Réinstaller le pied de la cale d'espacement a I'aide de la vis n® 8-18 x précédemment retirée, 8. Enlever, faire pivoter et réinstaller les pieds installés au niveau avant gauche, arriéré droit et arriéré gauche du four en suivant la mémé méthode. 5. Passer a la section “Raccordement électrique”. 6.
Four double En modifiant le positionnement des pieds du four, on peut installer un four double dans une cavité d'encastrement d'une hauteur comprise entre 48%" (124,1 cm) et 52%" (132,6 em). Consulter les instructions suivantes pour adapter la position des pieds 4 la taille de la cavité d'encastrement. La hauteur de la cavité d’encastrement est comprise entre 487%" (124,1 cm) et 50%" (128,1 cm) H n'est pas nécessaire d’installer les pieds du four. Le four a été correctement configuré & sa sortie d'usine.
6. A raide d’au mains 2 persanes, placer le four en position 3. De la mémé manière, installer un pied sur la partie ânière verticale. droite du four. 4. Installer un pied avant sur la partie avant gauche avec une vis n° 8-18 x 3%". REMARQUE : Positionner le pied de faon a ce que le coté long du pied soit orients vers le sommet du four, tel illustrer, A. Pied avant BVisn® 8 185%" 7. Passer a la section “Raccordement électrique”. GC.
Fours doubles Fours simples Tag RE natte [aid Risque de choc électrique Risque de choc électrique Déconnecter Ia source de courant électrique avant Déconnecter la source de couramment électrique avant T'entretien. d'entreprendre le travail. Utiliser du fil en cuivre rigide de calibre 8. Utiliser du fil en cuivre rigide de calibre 12. Relier le four a la terre. Relier le four a la terre.
Câble 4 4 conducteurs depuis le point de distribution du domicile Câble a 3 conducteurs depuis le point de distribution du domicile seulement IMPORTANT : Utiliser le câble a 4 conducteurs provenant du point de distribution du domicile aux États-Unis lorsque les codes locaux ne permettent pas la mise 4 la terre par Intermédiaire du conducteur neutre, en cas de nouvelle installation avec alimentation par un circuit secondaire (1996 NEC), dans les résidences mobiles et les véhicules récréatifs, dans les nouvel
1. Al'aide dau moins 2 personnes, soulever et introduire partiellement le four dans "ouverture d'encastrement du placard. Utiliser [ouverture du four comma zone de prise. REMARQUE : Pour introduire le four dans le placard, pousser contre la zone du joint du four située sur le châssis avant. Ne pas pousser contre les bords externes. 2.
7. L'évent inférieur ef la garniture de F'évent inférieur {nécessaires lorsque le four est installé avec les pieds en position haute} sont livrés dans |'emballage en mousse situ sur Je dessus du four, Pour installer 'évent inférieur uniquement, voir les instructions suivantes. Pour installer 'évent inférieur et la garniture de I'évent inférieur (pour les installations dont les pieds sont en position haute), voir les instructions de {'étape 8.
Hal Sur les fours simple ou double installés au-dessus d'un troll 2. Installer le déflecteur pour torii-réchaud (B) sur la pièce réchaud, la pose d'un déflecteur de tiroir-réchaud est nécessaire, d'évent inférieur (0) 4 I'aide de deux vis n° 8-18 x 16" de Voir fa section “Outillage et pièces” pour des renseignements sur chacune cote, le processus de commande. REMARQUE : Sur les modales de 27° (66.
reste une place, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée. 2. Vérifier la présence de tous les outils, 3. Jeter/recycler fous les matériaux d’emballage. 4, Pour l'utilisation et le nettoyage du four, lire le Guide utilisation et d’entretien. Vérification du fonctionnement pour un four simple tenu four double 1. Métré 'appareil sous tension. 2. Ala première utilisation, régler horloge et toute autre préférence réglable.