Owner's Manual
Table Of Contents
- BUILT-IN OVEN SAFETY
- Built-In Oven Safety_WOBIMW_OM_W11340821A
- OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean (on some models)
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Positioning Oven Feet for Multiple Cabinet Cutout Heights
- Make Electrical Connection
- Install Oven
- Replace Oven Door(s)
- Complete Installation
- SECURITE DU FOUR ENCASTRE
- Sécurité du four encastré
- ENTRETIEN ET REPARATION DU FOUR
- Nettoyage général
- Programme d’autonettoyage
- Steam Clean (nettoyage à la vapeur) (sur certains modèles)
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- INSTALLATIONS
- Préparer le four encastré
- Enlever la/les porte(s) du four
- Positionner les pieds du four pour des ouvertures de découpe dans l’armoire
- Raccordement électrique
- Installation du four
- Réinstallation de la/des porte(s) du four
- Achever l’installation
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
19
6. After the bottom vent shield is installed.
� Align the bottom vent trim tab (B) with the oven frame (A)
as shown.
� Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side of
the trim tab (B), align the top of the bottom trim tab (B) to
the Hinge receiver (D) as shown.
� Fasten the bottom vent trim securely to the oven frame (A).
A. Oven frame
B. Trim tab
C. #8-18 x 3/8" (9.5 mm)
screw
D. Hinge receiver
7. Replace the oven racks.
8. Replace the oven door. See the “Replace Oven Door(s)”
section.
9. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Oven” section.
10. Repeat for lower oven door.
IMPORTANT: For proper oven operation, check that the gap
between bottom of the door and bottom vent trim is at least
1/4" (6.4 mm).
11. Reconnect power.
12. The display panel will light and boot up.
13. If the display panel does not light, reference the Warranty.
Replace Oven Door(s)
1. Using two hands, grasp side edges of door at the midpoint.
Face the oven cavity.
2. Locate the slots on each side of the oven cavity for the door
hinge locks.
A. Slot in the oven cavity for door hinge lock
3. Using 2 hands, grasp the edges of the oven door. At a 45°
angle, insert the hinges at the same time, and push the oven
door into the oven cavity slot to replace. You may need to
gently shift the door from side to side as you push.
4. Make sure the door hinge notch is engaged on the bottom
of the oven cavity slot.
IMPORTANT: Do not close the door at this step or damage
may occur to the door hinge.
5. Lower the oven door to the fully open position. If the oven door
does not open to a full 90°, repeat steps 1 through 3.
6. Locate the oven door hinge locks in the corners of the oven
door, and rotate the hinge locks toward the oven cavity to the
locked position.
7. After the door hinges have been locked, gently swing the door
upward to close. The door should not be forced closed.
A
C
B
D
B