Specification
Table Of Contents
- BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY
- Built-In Microwave/Oven Combination Safety
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean (On Some Models)
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Make Electrical Connection
- Install Oven
- Install Warming Drawer Deflector Kit
- Replace Oven Door(s)
- Complete Installation
- SECURITE DE L'ENSEMBLE FOUR ELECTRIQUE/FOUR A MICRO-ONDES ENCASTRE
- Sécurité de l’ensemble four électrique/four à micro-ondes encastré
- ENTRETIEN ET REPARATION DU FOUR A MICRO-ONDES
- Nettoyage général
- Programme d’autonettoyage
- Steam Clean (nettoyage à la vapeur) (sur certains modèles)
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- INSTALLATION
- Préparer le four encastré
- Enlever la/les porte(s) du four
- Raccordement électrique
- Installation du four
- Installer l’ensemble de déflecteurs pour tiroir-réchaud (uniquement pour les fours installés par-dessus des tiroirs-réchauds)
- Réinstallation de la/des porte(s) du four
- Achever l’installation
- SEGURIDAD DE LA COMBINACION DE HORNO MICROONDAS/HORNO INTEGRADO
- Seguridad de la combinación de horno de microondas/horno integrado
- MICROWAVE OVEN MAINTENANCE AND CARE
- Limpieza general
- Ciclo de autolimpieza
- Steam Clean (Limpieza con vapor) (en algunos modelos)
- INSTRUCCIONES DE INSTALACION
- REQUISITOS
- Herramientas y piezas
- Requisitos de ubicación
- Requisitos eléctricos
- INSTALACIONES
- Preparación del horno empotrado
- Retire las puertas del horno
- Hacer la conexión eléctrica
- Para instalar el horno
- Instale el kit de deflector para cajón de calentamiento (solo para hornos instalados encima de un cajón de calentamiento)
- Vuelva a colocar las puertas del horno
- Finalización de la instalación
13
4. Securely fasten the oven to the cabinet using the
#8-14 x 3/4" screws provided.
Insert the screws through hole in black trim aligning with hole
in oven frame. Do not overtighten screws.
A. Oven frame
B. Side trim hole
C. Side trim piece
5. The bottom vent trim and bottom vent shield are shipped in
the foam packing at the top of the oven.
� Align bottom vent shield tab (B) with oven frame (A) as
shown.
� Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side of
the bottom vent shield tab (B), fasten the vent securely to
the oven frame (A).
A. Oven frame
B. Bottom vent
shield tab
C. #8-18 x 3/8" screws
A
B
C
C
B
A
6. After the bottom vent shield is installed.
� Align the bottom vent trim tab (B) with the oven frame (A)
as shown.
� Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side of
the trim tab (B), align the top edge of the bottom vent trim
tab (E) with the hinge receiver edge (D) as shown.
� Fasten the bottom vent trim securely to the oven frame (A).
A. Oven frame
B. Trim tab
C. #8-18 x 3/8" (9.5 mm)
screw
D. Hinge receiver edge
E. Bottom Vent Trim Tab
top edge
7. Replace the oven racks.
8. Replace the oven door. See the “Replace Oven Door(s)”
section.
9. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Oven” section.
10. Repeat for lower oven door.
IMPORTANT: For proper oven operation, check that the gap
between bottom trim of the door and bottom vent trim is at least
1/4" (6.4 mm).
A
C
B
D E
B