Use and Care Manual
Table Of Contents
- BUILT-IN OVEN SAFETY
- Built-In Oven Safety
- OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Positioning Oven Feet for Multiple Cabinet Cutout Heights
- Make Electrical Connection
- Install Oven
- Install Warming Drawer Deflector Kit (Only for Ovens Installed Above Warming Drawers)
- Replace Oven Door(s)
- Complete Installation
- SECURITE DU FOUR ENCASTRE
- Securite du four encastre
- ENTRETIEN ET REPARATION DU FOUR
- Nettoyage general
- Programme d'autonettoyage
- Nettoyage a la vapeur
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pieces
- Exigences d'emplacement
- Specifications electriques
- INSTALLATION
- Preparer le four encastre
- Enlever la/les porte(s) du four
- Positionner les pieds du four pour des ouvertures de decoupe dans l'armoire
- Raccordement electrique
- Installation du four
- Installer l'ensemble de deflecteurs pour tiroir-rechaud (uniquement pour les fours installes par-dessus des tiroirs-rechauds)
- Reinstallation de la/des porte(s) du four
- Achever l'installation
- SEGURIDAD DEL HORNO INTEGRADO
- Seguridad del horno integrado
- MANTENIMIENTO Y CUIDADO DEL HORNO
- General Cleaning
- Ciclo de autolimpieza
- Steam Clean
- INSTRUCCIONES DE INSTALACION
- REQUISITOS
- Tools and Parts
- Location Requirements
- Requisitos electricos
- INSTALACIONES
- Preparacion del horno empotrado
- Retire las puertas del horno
- Ubicacion de las patas del horno para multiples alturas de corte del armario
- Como hacer la conexion electrica
- Install Oven
- Instale el kit de deflector para cajon de calentamiento (solo para hornos instalados encima de un cajon de calentamiento)
- Vuelva a colocar las puertas del horno
- Finalizacion de la instalacion
16
4. Install a front foot on the left front spacer using a #8-18 x 3/8"
(9.5 mm) screw.
NOTE: Position the foot so the long side of the foot is facing
toward the inside of the oven.
A. Front Foot
B. #8-18 x 3/8" (9.5 mm) screw
C. Spacer
5. In the same manner, install a front foot on the right front of the
oven.
6. Using 2 or more people, place the oven in its upright position.
7. Go to the “Make Electrical Connection” section.
Cutout Height is Between 51
3
/
16
" and 52
3
/
16
" (130.0 cm and
132.6 cm)
NOTE: For installation, the tall shield is also required to replace
the shield that came with the unit. Please refer to your Quick Start
Guide for the service number to call and request at no charge.
1. Using 2 or more people, place the oven on its back on a
covered surface.
2. Install a rear foot on the left rear spacer using a #8-18 x 3/8"
(9.5 mm) screw.
NOTE: Position the foot so the short side of the foot is facing
toward the top of the oven.
A. Spacer
B. Rear foot
C. #8-18 x 3/8" (9.5 mm) screw
3. In the same manner, install a foot on the right rear of the oven.