Use and Care Manual
Table Of Contents
- BUILT-IN OVEN SAFETY
- Built-In Oven Safety
- OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Positioning Oven Feet for Multiple Cabinet Cutout Heights
- Make Electrical Connection
- Install Oven
- Install Warming Drawer Deflector Kit (Only for Ovens Installed Above Warming Drawers)
- Replace Oven Door(s)
- Complete Installation
- SECURITE DU FOUR ENCASTRE
- Securite du four encastre
- ENTRETIEN ET REPARATION DU FOUR
- Nettoyage general
- Programme d'autonettoyage
- Nettoyage a la vapeur
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pieces
- Exigences d'emplacement
- Specifications electriques
- INSTALLATION
- Preparer le four encastre
- Enlever la/les porte(s) du four
- Positionner les pieds du four pour des ouvertures de decoupe dans l'armoire
- Raccordement electrique
- Installation du four
- Installer l'ensemble de deflecteurs pour tiroir-rechaud (uniquement pour les fours installes par-dessus des tiroirs-rechauds)
- Reinstallation de la/des porte(s) du four
- Achever l'installation
- SEGURIDAD DEL HORNO INTEGRADO
- Seguridad del horno integrado
- MANTENIMIENTO Y CUIDADO DEL HORNO
- General Cleaning
- Ciclo de autolimpieza
- Steam Clean
- INSTRUCCIONES DE INSTALACION
- REQUISITOS
- Tools and Parts
- Location Requirements
- Requisitos electricos
- INSTALACIONES
- Preparacion del horno empotrado
- Retire las puertas del horno
- Ubicacion de las patas del horno para multiples alturas de corte del armario
- Como hacer la conexion electrica
- Install Oven
- Instale el kit de deflector para cajon de calentamiento (solo para hornos instalados encima de un cajon de calentamiento)
- Vuelva a colocar las puertas del horno
- Finalizacion de la instalacion
19
4. Securely fasten the oven to the cabinet using the
#8-14 x 3/4" (1.9 cm) screws provided.
Insert the screws through hole in black trim aligning with hole
in oven frame. Do not overtighten screws.
A. Oven frame
B. Side trim hole
C. Side trim piece
5. The bottom vent trim and bottom vent shield are shipped in
the foam packing at the top of the oven.
Tall bottom vent shield are used when the oven is installed
with the feet in the tall position. Please contact service for one
to be shipped to you free of charge.
■ Align vent tab (B) with oven frame (A) as shown.
■ Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side of
the shield tab (B), fasten the vent securely to the oven
frame (A).
A. Oven frame
B. Shield tab
C. #8-18 x 3/8" (9.5 mm) screws
■ Fasten the bottom vent trim securely to the oven frame (A).
A
B
C
C
B
A
6. After the bottom vent shield is installed.
■ Align the bottom vent trim tab (B) with the oven frame (A)
as shown.
■ Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side
of the trim tab (B), align the top edge of the bottom vent
trim tab (E) with the hinge receiver edge (D) as shown.
A. Oven frame
B. Trim tab
C. #8-18 x 3/8" (9.5 mm)
screw
D. Hinge receiver edge
E. Bottom Vent Trim Tab
top edge
7. Replace the oven racks.
8. Replace the oven door. See the “Replace Oven Door(s)”
section.
9. Check that the door is free to open and close. If it is not,
repeat
the removal and installation procedures. See the
“Prepare Built-In Oven” section.
10. Repeat for lower oven door.
IMPORTANT: For proper oven operation, check that the gap
between bottom of the door and bottom vent trim is at least
1/4" (6.4 mm).
11. Reconnect power.
12. The display panel will light and boot up.
13. If the display panel does not light, reference the Warranty.
14. If F9E0 error code is encountered upon powering up the
unit, the appliance is wired incorrectly at the Junction Box or
Electrical Panel. Contact a qualified electrician to verify the
home electrical supply and the hardwire connection at the
Junction Box or Electrical Panel (See the Electrical
Connection Options section).
A
C
B
D
B
E