Instruction for Use

ManualsBrandsWhirlpool ManualsOtherWP 78/3

Whirlpool is a registered trademark of Whirlpool USA

Before using the dishwasher, read the

installation and maintenance instructions carefully!

5019 396 01140

WP 78

1) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different

loads, options, different sensor settings (only with sensor programmes), different water supply temperatures, as well as water

hardness and power supply voltage.

2) Reference programme for energy label in compliance with EN 50242. - Important information for Test Laboratories:

for

detailed information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of

November 2001.

1. OVERVIEW

On button

Off button

Delayed start button

Press the button repeatedly to delay the

start of the programme by 3, 6 or 9 hours.

Then press the START button. The

dishwasher will start at the set time.

Detergent setting upon initial use and when using a different type of

detergent

1. Select the third programme in the relative table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, select the desired detergent:

“3h” = 2in1, “6h” = 3in1, “9h” = other combined action detergents

(in this way, the rinse aid and/or salt indicator is deactivated). All 3

LEDs light up = Powder detergent (factory setting).

4. Switch the appliance off and then switch it on again. The selected

detergent type will be indicated on the display by the

corresponding LEDs for approx. 3 seconds.

Programme selection button

Press the button repeatedly until the desired programme

indicator lights up.

Start button

Switches “on” when the dishwasher is operating.

Flashes when a fault occurs. Switches off at the end of

the programme.

START button RESET function:

Press this button for at least 2 seconds; the selected

programme and options are cancelled. Main failure

displays (repeated flashing of the START indicator lamp)

can be cancelled by RESETTING. Detailed instructions

are given in chapter 5 “What to do if...”.

Rinse aid level indicator and salt level indicator

These indicator lamps light up when rinse aid or salt

need to be added. Add just before starting a wash

programme.

Table 1.1.

Programme chart

Detergent

dispenser

Consumption

Programmes

Available

options

Loading instructions large small Litres kWh Minutes

Sensor Intensive 60-70°C

Automatic programme

recommended for heavily

soiled crockery with dried-on

or burnt food, for example

pans and saucepans.

X X 13-20 1.10-2.00 100-150 ±

Quickwash 40°C

Lightly soiled crockery, with

no dried-on food.

X — 10.0 0.65 30 ±

Eco

50°C

Normally soiled crockery. X X 12.0 1.05 165 ±

Antibacterial

Normally or heavily soiled

crockery, with additional

antibacterial wash. Programme

interruption (e.g due to door

opening) can compromise

elimination of germs.

X X 13,0 1,50 115 ±

Power Clean 70°C

Recommended programme for

heavily soiled crockery, especially

suitable for pans and saucepans.

Intensive wash with additional

water jets.

X X 16.0 1.80 220 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB WP 78 1. OVERVIEW Programme selection button Press the button repeatedly until the desired programme indicator lights up. On button Start button Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme. START button RESET function: Press this button for at least 2 seconds; the selected programme and options are cancelled.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given in the following pages, see also chapter “5. What to do if...” 1. Switch on the appliance Open the dishwasher door. Press the ON button. 2. Select a programme Press the button or to bring up the desired programme on the display. Select options, if available. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1. Overview” provides instructions for selecting detergent type. 4.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button or to bring up the desired programme on the display. The appliance must be switched on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate programmes and relative available options are detailed in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the lever 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. USING THE APPLIANCE LOADING THE RACKS TOP RACK - depending on model Multipurpose support A Three possible positions for long for utensils, cups and glasses. Dish holder B In horizontal position for cups/long utensils, in raised position for plates and stemware. Adjustable glass holder C Depending on the position, for small glasses or stemware. Long utensils (kitchen knives) must be placed with the tips towards the appliance.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of the Eco programme 50°C (if available), from time to time select the intensive 70°C programme (if available). The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).