Dimensions

PRODUCT MODEL NUMBERS
Because Whirlpool Corporation includes a continues commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10575959A
05/06/2016
WGI925C0BWGE755C0BWGE555S0B
WGE745C0F
30" (76 cm) Freestanding Electric Range
Electrical Connection:
To properly install your range, you must determine the type of electrical
connection you will be using and follow the instructions provided for it
here.
■ Range must be connected to the proper electrical voltage and
frequency as specified on the model/serial rating plate. The model/
serial rating plate is located behind the control panel. Refer to the
figures in “Product Dimensions” in the “Location Requirements”
section.
■ This range is manufactured with the neutral terminal connected to
the cabinet. Use a 3-wire, UL listed, 40- or 50- amp power supply
cord (pigtail) (see the following Range Rating chart). If local codes
do not permit ground through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40- or 50-amps and investigated for use with
ranges.
Range Rating*
Specified Rating of Power Supply
Cord Kit and Circuit Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50**
16.6 - 22.5 KW 12.6 - 18.5 KW 50
* The NEC calculated load is less than the total connected load listed on
the model/serial rating plate.
** If connecting to a 50-amp circuit, use a 50-amp rated cord with kit. For
50-amp rated cord kits, use kits that specify use with a nominal 1
3
/
4
"
(34.9 mm) diameter connection opening.
■ A circuit breaker is recommended.
■ The range can be connected directly to the circuit breaker box (or
fused disconnect) through flexible or nonmetallic sheathed, copper or
aluminum cable. See the “Electrical Connection - U.S.A. Only” section.
Cabinet opening dimensions shown are for: 25" (63.5 cm) countertop
depth, 24" (61 cm) base cabinet depth, and 36" (91.4 cm) countertop
height
IMPORTANT: If installing a range hood or microwave hood combination
above the range, follow the range hood or microwave hood combination
installation instructions for dimensional clearances above the cooktop
surface.
A freestanding range may be installed next to combustible walls with
zero clearance.
CABINET OPENING DIMENSIONS
PRODUCT DIMENSIONS
A. 35
3
/
4
" ±
1
/
8
" (90.8 cm ± 0.3 cm)
cooktop height (minimum) with
leveling legs screwed all the
way in*
B. Model/serial/rating plates
(located behind the control
panel)**
C. 47
1
/
8
" ±
1
/
8
" (119.7 cm ± 0.3 cm)
overall height (minimum) with
leveling legs screwed all the
way in*
D. 28
1
/
2
" ±
1
/
4
" (72.4 cm ± 0.6 cm)
depth with handle
E. 26
1
/
8
" ±
1
/
8
" (66.4 cm
± 0.3 cm)***
F. 29
15
/
16
" ±
1
/
16
" (76.0 cm
± 0.2 cm) width
* Range can be raised approximately 1" (2.5 cm) by adjusting the
leveling legs.
** Model/serial/rating plates may be rotated up from behind the control
panel for viewing from the front of the range.
*** Excludes handle. Dimension given is from wall to front of oven door
and will vary based on electric outlet receptacle installation.
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. 30" (76.2 cm) min. opening width
F. Cabinet door or hinge should not extend into cutout*
G. 1
1
/
2
" (3.8 cm) min. from right side cabinet
H. 2" (5.1 cm) min. from floor
I. 7" (17.8 cm) min. from floor
J. 8" (20.3 cm) width
K. 3 " (8.91 cm) min. from floor
Proper positioning of outlet shown above.
* Nothing located in shaded areas can extend more than 1
1
/
2
" (3.8 cm)
from wall or range will not slide all the way back.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is
covered by not less than
1
/
4
" (0.64 cm) flame retardant millboard covered
with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless
steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
B**
A*
F
E***
D
C*
A
B
C
D
E
F
G
H
I
J
K