Use and Care Guide

ManualsBrandsWhirlpool ManualsWasher & Dryer SetWhirlpool WPWADREBK96201

If you experience Possible Causes Solution

Error Code Appears in Display

Once any possible issues are corrected, touch the POWER button once to clear the code. Reselect and restart the cycle.

F0E1

Load detected

in Clean Washer

with affresh

cycle

Items detected in the washer when

running a Clean Washer with affresh

cycle.

Remove load and restart the Clean Washer with affresh

cycle.

F0E2

Oversuds detection

Excessive suds in washer. Washer

is running a suds reduction routine.

Allow the wash cycle to continue.

Use only HE detergent.

F0E5 (OB)

Off balance load

detected

Load could be unbalanced or too

large.

Avoid tightly packing the washer. Avoid washing single items.

Balance a single item with such as a rug or jeans with a few

extra items.

F1E1

ACU memory corruption or

hardware failure/ACU main

relay cannot be opened or

closed

Problem detected with the washer. Try resetting the washer by unplugging it from the outlet

and then plugging it back in. If unsuccessful, call for service.

F1E2

MCU memory corruption

or hardware failure

Problem detected with the washer. Try resetting the washer by unplugging it from the outlet

and then plugging it back in. If unsuccessful, call for service.

F3E1

Analog pressure failure

Problem detected with the pressure

sensor.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F3E2

Wash NTC failure

Open circuit or short circuit fault

detected.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F3E5

Dry NTC failure

Open circuit or short circuit fault

detected. The wash function is still

operable, but the dry function will

not operate.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F3E6

Accelerometer failure

Accelerometer failed self test or

experienced orientation error.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F4E1

Water heater relay failure

Problem detected with the water

heater. There is a water heater relay

short error or feedback failure.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F4E2

Wash heater relay circuit

fault

Wash heater relay is detected as not

closed.

Call for service

F4E4

Fan drive failure

Dry fan triac open circuit, short circuit,

diode mode, or feedback KO fault

detected.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F5E1

Door switch failure

Problem detected with the door

switch. Door is unlocked during a

cycle when it should be locked.

Try resetting the washer by unplugging it from the outlet and

then plugging it back in. If unsuccessful, call for service.

F5E2

Door cannot be locked

Problem detected with the door lock. Try resetting the washer by unplugging it from the outlet

and then plugging it back in. If unsuccessful, call for service.

F5E3

Door cannot be unlocked

Problem detected with the door lock. Try resetting the washer by unplugging it from the outlet

and then plugging it back in. If unsuccessful, call for service.

F5E4 (DR)

Door not open between

consecutive cycles

Door not open between consecutive

cycles.

Open and close the door before restarting the cycle.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.