Owner's Manual
Table Of Contents
- REFRIGERATOR SAFETY
- MAINTENANCE AND CARE
- Cleaning
- Changing the LED Module
- Water Filtration System
- Vacation and Moving Care
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Electrical Requirements
- Location Requirements
- Water Supply Requirements
- Connect the Water Supply
- REFRIGERATOR FEATURES
- Crisper Humidity Control
- DOOR AND HANDLE INSTRUCTIONS
- Refrigerator Doors and Drawer
- Remove and Replace Door Handles
- Remove Doors and Hinges
- Reverse Doors (optional)
- Replace Doors and Hinges
- Remove and Replace Freezer Drawer
- PERFORMANCE DATA SHEET
- Performance Data Sheet
- SÉCURITÉ DU RÉFRIGÉRATEUR
- Sécurité du réfrigérateur
- ENTRETIEN ET RÉPARATION
- Nettoyage
- Remplacer le module à DEL
- Système de filtration de l’eau
- Précautions à prendre avant les vacances ou le déménagement
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Spécifications électriques
- Exigences d’emplacement
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- CARACTÉRISTIQUES DU RÉFRIGÉRATEUR
- Réglage de l’humidité dans le tiroir à légumes
- INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE
- Portes et tiroir du réfrigérateur
- Consulter la section Retrait et réinstallation des poignées de porte
- Démontage des portes et charnières
- Inversion des portes (facultatif)
- Réinstallation des portes et charnières
- Retrait et réinstallation du tiroir de congélation
- FICHE DE DONNÉES DE PERFORMANCE
- Fiche de données de performance
14
Remove and Replace Freezer Drawer
IMPORTANT:
� Two people may be required to remove and replace the
freezer drawer.
REMOVE DRAWER FRONT
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front as shown below.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
A. Four Bracket screws
3. Lift drawer front upward and off the screws.
Replace Drawer Front
1. Slide the drawer glides out of the freezer compartment. Insert
the screws in the top of the drawer front into the slots in the
drawer brackets as shown below.
2. Pull the drawer brackets toward you to insert the two screws in
the bottom of the drawer front into the brackets as shown
below..
3. Completely tighten the four screws.
Final Steps
1. Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover.
2. Replace the base grille.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
3. Plug into a grounded 3 prong outlet.
4. Return all removable door parts to door and food to
refrigerator.
Door Closing and Door Alignment
The base grille covers the leveling screws and roller assemblies
located at the bottom of the refrigerator cabinet below the freezer
door or drawer. Before making adjustments, remove the base
grille and move the refrigerator to its final location.
1. Remove the two screws fastening the base grille to the
cabinet, and set the screws aside. Grasp the grille and pull it
toward you.
2. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs off the floor by turning the leveling screws
counterclockwise. The front rollers will be touching the floor.