Owners Manual
Table Of Contents
- REFRIGERATOR SAFETY
- Refrigerator Safety
- REFRIGERATOR CARE
- Cleaning
- Changing the LED Module
- Refrigerator Shelves
- Opening and Closing Doors
- Vacation and Moving Care
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Connect the Water Supply
- Complete the Installation
- Install Air Filter (on some models)
- Install Produce Preserver (on some models)
- REFRIGERATOR FEATURES
- Crisper Humidity Control (on some models)
- Water and Ice Dispensers (on some models)
- Ice Maker and Storage Bin
- Water Filtration System
- DOOR AND HANDLE INSTRUCTIONS
- Door and Drawers
- Remove and Replace Handles
- Remove Refrigerator Doors and Hinges
- Reset Bottom Refrigerator Door Hinge
- Replace Refrigerator Doors and Hinges
- Remove and Replace Refrigerator Drawer
- Door Closing and Alignment
- PERFORMANCE DATA SHEET
- Performance Data Sheet
- SÉCURITÉ DU RÉFRIGÉRATEUR
- Sécurité du réfrigérateur
- ENTRETIEN DU RÉFRIGÉRATEUR
- Nettoyage
- Remplacer le module à DEL
- Tablettes du réfrigérateur
- Ouverture et fermeture des portes
- Précautions à prendre avant les vacances ou le déménagement
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- Terminer l’installation
- Installer le filtre à air (sur certains modèles)
- Installation du conservateur de produits frais (sur certains modèles)
- CARACTÉRISTIQUES DU RÉFRIGÉRATEUR
- Commande d’humidité dans le bac à légumes (sur certains modèles)
- Distributeur d’eau et de glaçons (sur certains modèles)
- Machine à glaçons et bac d’entreposage
- Système de filtration de l’eau
- INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE
- Porte et tiroirs
- Pour enlever et réinstaller les poignées
- Démontage des portes et charnières du réfrigérateur
- Réinitialiser la charnière inférieure du réfrigérateur
- Réinstallation des portes et charnières
- Retrait et réinstallation du tiroir de congélation
- Fermeture et alignement des portes
- FICHE DE DONNÉES DE PERFORMANCE
- Fiche de données de performance
27
Tools Needed: Phillips screwdriver
1. With the drawers closed, identify the drawer front that needs
to be raised or lowered.
2. Open the drawer to its full extension, and remove the interior
bin.
3. Locate the drawer glide brackets.
A. Drawer glide brackets
4. Insert the Phillips screwdriver into tightening screw and turn
counterclockwise to loosen the drawer front.
A. Tightening screw B. Adjusting screw
5. Insert the Phillips screwdriver into adjusting screw to adjust
the drawer front.
IMPORTANT: The direction you turn the adjusting screw
depends on which side of the drawer you are adjusting.
Left-Hand Side Drawer Glide
� To raise the drawer front, turn adjusting screw clockwise.
� To lower the drawer front, turn adjusting screw
counterclockwise.
Right-Hand Side Drawer Glide
� To raise the drawer front, turn adjusting screw
counterclockwise.
� To lower the drawer front, turn adjusting screw clockwise.
6. Insert the Phillips screwdriver into tightening screw, and turn
clockwise to tighten the drawer front.
7. Close the refrigerated drawer to check the alignment. Repeat
steps 2 through 6 until the drawer fronts are level.
Step 2 - Adjust the Drawer Fronts Side to Side
IMPORTANT: Each refrigerated drawer can be adjusted side to
side on both the left and right side.
1. With the drawers closed, identify the drawer that is not
aligned.
2. Open the drawer to its full extension, and remove the interior
bin.
3. Locate the drawer glide brackets.
4. Starting with the glide bracket closest to the vertical gap, press
and hold the release lever up. With your other hand, lift the
door clip from the drawer glide bracket.
A. Drawer front clip C. Release lever
B. Drawer glide bracket
5. Reposition the drawer front clip onto the drawer glide bracket
in the direction you want to move the drawer front. Make sure
that the glide bracket is vertically level.
6. Release the lever to lock the glide bracket into position.
7. Repeat steps 3 through 6 for the other side of the drawer front.
NOTE: Adjust the clip on the top of the second glide bracket
so that it is in the same position as the side you adjusted first.
8. Close the drawer and visually inspect the gap. Repeat steps 2
though 7 until the drawer fronts are aligned.
FINAL STEPS
1. Replace the interior drawer bins.
NOTE: The bins must be placed into the drawers correctly so
that the refrigerated drawers will close and operate properly.
See “Remove and Replace Drawer Fronts.”
2. Close the refrigerated drawers.