Owners Manual
Table Of Contents
- REFRIGERATOR SAFETY
- Refrigerator Safety
- MAINTENANCE AND CARE
- Cleaning
- Lights
- Freezer Shelf (number varies by model)
- Vacation and Moving Care
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Connect Water Supply
- Complete the Installation
- Install Air Filter (on some models)
- Install Produce Preserver (on some models)
- REFRIGERATOR FEATURES
- Convertible Drawer Temperature Control (on some models)
- Crisper Humidity Control (on some models)
- Dual Evaporator (on some models)
- Water and Ice Dispensers
- Ice Maker and Storage Bin
- Water Filtration System
- DOOR REMOVAL AND LEVELING STYLE 1
- Door Instructions
- Install and Remove Door Handles
- Remove Doors and Hinges
- Replace Doors and Hinges
- Door Closing and Alignment
- DOOR REMOVAL AND LEVELING STYLE 2
- Door Instructions
- Install and Remove Door Handles
- Remove Doors and Hinges
- Door Closing, Leveling, and Alignment
- PERFORMANCE DATA SHEET
- SECURITE DU REFRIGERATEUR
- Sécurité du réfrigérateur
- ENTRETIEN ET REPARATION
- Nettoyage
- Lampes
- Tablettes du congélateur (le nombre varie selon le modèle)
- Précautions à prendre avant les vacances ou le déménagement
- INSTRUCTIONS D'INSTALLATION
- Déballage du réfrigérateur
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- Terminer l’installation
- Installer le filtre à air (sur certains modèles)
- Installation du conservateur de produits frais (sur certains modèles)
- CARACTERISTIQUES DU REFRIGERATEUR
- Commande de température dans le tiroir convertible (sur certains modèles)
- Commande d’humidité dans le bac à légumes (sur certains modèles)
- Évaporateur double (sur certains modèles)
- Distributeurs d’eau et de glaçons
- Machine à glaçons et bac d’entreposage
- Système de filtration de l’eau
- RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU, STYLE 1
- Instructions pour la porte
- Installation et retrait des poignées de la porte
- Démontage des portes et charnières
- Réinstallation des portes et charnières
- Fermeture et alignement des portes
- RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU, STYLE 2
- Instructions pour la porte
- Installation et retrait des poignées de la porte
- Démontage des portes et charnières
- Fermeture, mise à niveau et alignement des portes
- FICHE DE DONNEES RELATIVES AU RENDEMENT
9
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn cooling off or turn the control
(thermostat, refrigerator, or freezer control depending on the
model) to Off. Then disconnect the refrigerator from the electrical
source. When you are finished, reconnect the refrigerator to the
electrical source. Turn cooling on or reset the control (thermostat,
refrigerator, or freezer control depending on the model) to the
desired setting. See “Control Descriptions” in the Quick Start
Guide.
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed:
� Flat-blade screwdriver
� 7/16" and 1/2" open-end or two
adjustable wrenches
� 1/4" nut driver
� 1/4" drill bit
� Cordless drill
NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shutoff valve, a union, and copper or PEX
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing-
type or 3/16" (4.76 mm) saddle valve, which reduces water flow
and clogs more easily.
IMPORTANT:
� All installations must meet local plumbing code requirements.
� Use copper or PEX tubing and check for leaks. Install copper
or PEX tubing only in areas where the household temperatures
will remain above freezing.
Water Pressure
A cold water supply with water pressure of between 30 and 120
psi (207 and 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
If your refrigerator has a water dispenser: After installation is
complete, use the water dispenser to check the water pressure.
� With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup of water is dispensed in 8 seconds or less, the
water pressure to the refrigerator meets the minimum
requirement.
� If it takes longer than 8 seconds to dispense 1 cup of water, the
water pressure to the refrigerator is lower than recommended.
See online “Troubleshooting” for suggestions.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and 827
kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
� Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
� Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
� If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water Filtration
System”.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Connect Water Supply
Read all directions before you begin.
IMPORTANT:
� Connect to potable water supply only.
� Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
� The gray water tubing on the back of the refrigerator (which is
used to connect to the household water line) is a PEX (cross-
linked polyethylene) tube. Copper or PEX tubing connections
from the household water line to the refrigerator are
acceptable, and will help avoid off-taste or odor in your ice or
water. Check for leaks. For recommended parts if PEX tubing
is used instead of copper:
W10505928RP (7 ft. [2.14 m] jacketed PEX),
8212547RP (5 ft. [1.52 m] PEX), or
W10267701RP (25 ft. [7.62 m] PEX).
� Install tubing only in areas where temperatures will remain
above freezing.
Tools Needed:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
� Flat-blade screwdriver
� 7/16" and 1/2" open-end wrenches or two adjustable wrenches
� 1/4" nut driver
Connect to Water Line
IMPORTANT: If you turn on the refrigerator before the water line is
connected, turn off the ice maker.
Style 1 (Recommended)
1. Unplug refrigerator or disconnect power.
2. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
3. Use a quarter-turn shutoff valve or the equivalent, served by a
1/2" copper or PEX household supply line.
NOTE: To allow sufficient water flow to the refrigerator, a
minimum 1/2" size copper or PEX household supply line is
recommended.
A. Bulb
B. Nut
C. Copper or PEX tubing (to refrigerator)
D. Household supply line (½" minimum)