Dispensing Guide

1
SIDE-BY-SIDE REFRIGERATOR DISPENSERS
SSiiddee--BByy--SSiiddee WWaatteerr aanndd IIccee DDiissppeennssiinngg GGuuiiddee
TO DISPENSE WATER (STANDARD):
1. Press a sturdy glass against the water dispenser paddle. Hold
the glass close to the water dispenser spout to ensure that the
water dispenses into the glass.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according to
the volume you selected. The flow of water will automatically
stop once the desired volume has been dispensed.
2. To stop dispensing, remove the glass from the dispenser
paddle.
TO DISPENSE WATER (MEASURED FILL):
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons.
IMPORTANT: Low water pressure may affect the accuracy of this
feature.
NOTE: The amount of water you select will be dispensed. Be sure
that the container is empty and can hold the entire volume. If ice is
in the container, you may need to adjust your selection.
NOTE: Household water pressure may affect the accuracy of the
Measured Fill feature. For optimum performance of your water
dispenser, you must first calibrate Measured Fill.
How to calibrate Measured Fill:
IMPORTANT: Flush the water system before calibrating Measured
Fill. See “Flush the Water System” in the Owner’s Manual.
1. Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray, centered in front of the water dispenser pad.
NOTE: Depending on your model, a measuring cup may be
provided.
2. Press and hold the Options and Lock buttons at the same time
for 3 seconds. The words “Back” and “1 Cup” will appear on the
display screen. Also, “Calibrate” will illuminate and remain lit
while the Measured Fill feature is being calibrated.
NOTE: You may press the Ice Type button under the word
“Back” at any time to exit calibration mode. The display
screen's “Calibrate” text will turn off.
3. Using your hand (not the measuring cup), press and release
the water dispenser paddle in order to dispense water to the
1 cup fill line.
NOTE: If overfilling or spilling occurs, discard the water and
press “Back” to restart the calibration process.
4. When 1 cup of water has been correctly dispensed into the
measuring cup, press the Measured Fill button under the word
“Confirm” to confirm the calibration.
When Measured Fill calibration has been confirmed, the display will
return to the home screen.
1. Press Measured Fill to turn on the feature. When the feature is
on, the Measured Fill screen appears on the display.
Press Ice Type to manually turn off the Measured Fill feature.
NOTE: The dispenser will automatically turn off Measured Fill after
1 minute of inactivity. When Measured Fill is turned off, any
changes you have made will be lost and all defaults will be
restored.
2. You can dispense water by the ounce, cup, or liter. The default
unit is ounces. To switch to cups or liters, press the Light
button. Default, minimum, and maximum volumes are listed
below.
Units Default Minimum Maximum
Ounces 8 1 128
Cups 1 1/4 16
Liters 0.25 0.05 4.00
3. Press the Lock and Options buttons to adjust the volume as
desired. The Lock button increases the volume, and the
Options button lowers the volume.
NOTES:
When increasing or decreasing the volume, the control may
stop responding if an adjustment button is held for
approximately 10 seconds or longer. Release the button for
approximately 2 seconds; then continue making
adjustments.
Most coffee cups (commonly 4 to 6 oz. [118 to 177 mL] per
cup) are not the same size as a measuring cup (8 oz. [237
mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.

Summary of content (6 pages)