Owners Manual

7
Reverse Doors (optional)
IMPORTANT: If you want to reverse your doors so that they
open in the opposite direction, follow these steps. If you are not
reversing the doors, see “Replace Doors and Hinges.”
Style 1 - Standard Door models
Graphics follow these instructions.
Cabinet
1. Remove the three dome caps and the screws from handle
side and move them to opposite side. See Graphic 1-1.
2. Remove cabinet hinge hole plugs from cabinet top and move
them to opposite side hinge holes as shown. See Graphic 1-2.
Freezer Door
1. Remove the screw cover. See Graphic 2.
2. Remove the freezer handle assembly as shown. Keep all parts
together. See Graphic 2.
3. Remove door hinge hole plug from freezer door. Move to
opposite side hinge hole as shown. See Graphic 3.
4. Remove the brand badge using the plastic tool (provided).
Replace it with the badge provided in the Reversibility Kit
located inside the crisper drawer. For proper placement, see
the Brand Badge Placement template (the last page of this
manual).
NOTES:
■ To avoid scratching the nish, do not use a sharp or
metallic object to pry the brand badge from the door.
■ Rub a small amount of liquid dish soap over any adhesive
residue with your ngers. Rinse the door with warm water
and dry with a soft cloth.
5. Remove door stop. Move to opposite side of refrigerator door
as shown. See Graphic 5.
6. Position freezer handle on opposite side of the freezer door as
shown. See Graphic 2. First, drive the bottom two screws into
handle. Align upper portion of handle and drive top screw into
handle.
7. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.
8. Replace screw cover. See Graphic 2.
Refrigerator Door
1. Remove the screw cover. See Graphic 6.
2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 6.
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown. See Graphic 3.
4. Remove door handle sealing screws. Move to opposite side
of refrigerator door as shown. See Graphic 4.
5. Remove door handle hole plug and discard.
See Graphic 7. Replace on opposite side with the door handle
hole plug provided in the Reversibility Kit located in the
crisper.
6. Remove door stop. Move to opposite side of refrigerator door
as shown. See Graphic 5.
7. Position refrigerator handle on opposite side of the refrigerator
door as shown. See Graphic 6. First, drive top two screws in
handle rst. Align lower portion of handle and drive bottom
screw into handle.
8. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on refrigerator.
9. Replace screw cover. See Graphic 6.
Style 2 - Contour Door models
Graphics follow these instructions.
Cabinet
1. Remove the three dome caps and screws from handle side
and move them to opposite side. See Graphic 1-1.
2. Using the three 5⁄16" hex-head hinge screws, rinsert two
screws halfway into the holes, leaving space to insert the
Center Hinge.
3. Slide the center hinge, from the right, onto the screws, insert
the third screw, and tighten all screws completely.
NOTE: Make sure the washers are in place on both the top
and bottom pins of the center hinge.
4. Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes as shown. See
Graphic 1-2.
Freezer Door
1. Remove the freezer door handle. Using a 1/8" hex key, loosen
the setscrew located on the side of the handle. Pull the
handle straight out from the door. Keep all parts together. See
Graphic 2.
Door Stop Screw
Door Handle Sealing Screw
Flat-Head Handle Screw
Door Handle Hole
Plug
Door Hinge Hole Plug
Cabinet Hinge Hole Plu
g
Dome Cap
Dome Cap Washer
Door
Hinge
Hole Plug
Cabinet Hinge
Hole Plug
Dome Cap
Washer
Dome Cap
Setscrew
Shoulder
Screw
Shoulder
Screw Washer
Screw
Door
Stop
Flat-Head
Handle
Screw
Door Handle
Hole Cap
A
A
B
A. 5⁄16" hex-head hinge screws
B. Washers