Owner's Manual
Table Of Contents
- REFRIGERATOR SAFETY
- Refrigerator Safety
- MAINTENANCE AND CARE
- Cleaning
- Changing the Light Bulbs
- Vacations
- Moving
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Connect the Water Supply
- Install Air Filter
- REFRIGERATOR DOORS
- Door and Handle Instructions
- Remove Doors and Hinges
- Reverse Doors and Hinges (optional)
- Replace Doors and Hinges
- Final Steps
- Reversibility Kit Instructions
- Adjust the Doors
- REFRIGERATOR AND FREEZER FEATURES
- Refrigerator Shelves
- Freezer Shelf
- Door Rails or Trivets
- Can Racks and Bins (on some models)
- Deli or Meat Drawer
- Crisper
- Utility Compartment
- Ice Maker
- SÉCURITÉ DU RÉFRIGÉRATEUR
- Sécurité du réfrigérateur
- ENTRETIEN ET RÉPARATION
- Nettoyage
- Remplacement des ampoules d’éclairage
- Vacances
- Déménagement
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- Installation du filtre à air
- PORTES DU RÉFRIGÉRATEUR
- Instructions pour la porte et la poignée
- Démontage des portes et charnières
- Inversion du sens d’ouverture des portes et d’installation des charnières (facultatif)
- Réinstallation des portes et charnières
- Étapes finales
- Instructions pour l’ensemble d’inversion du sens d’ouverture
- Ajustement des portes
- CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ET DU CONGÉLATEUR
- Tablettes du réfrigérateur
- Tablette de congélateur
- Tringles de la porte ou balconnets
- Cannettes et balconnets de porte (sur certains modèles)
- Tiroir à viande ou à charcuterie
- Bac à légumes
- Compartiment utilitaire
- Machine à glaçons
10
Reverse Doors and Hinges (optional)
IMPORTANT: If you want to reverse your doors so that they open
in the opposite direction, follow these steps. If you are not
reversing the doors, see “Replace Doors and Hinges.”
Style 1 - Standard Door Models
Graphics follow these instructions.
Door Stop
Screw
Dome Cap Cabinet Hinge
Hole Plug
Door Handle
Hole Plug
Door Handle
Sealing Screw
Flat-Head
Handle Screw
Dome Cap
Washer
Door Hinge
Hole Plug
Cabinet
1. Remove the three dome caps and the screws from handle
side and move them to opposite side.
A. Dome cap washers C. Dome Caps
B. Hex-head hinge screws
2. Remove cabinet hinge hole plugs from cabinet top and move
them to opposite side hinge holes as shown below..
A. Cabinet Hinge Hole Plugs
Freezer Door
1. Remove the screw cover.
2. Remove the freezer handle assembly as shown below. Keep
all parts together.
A. Screw Cover C. Freezer Handle
B. Handle Screw D. Flat-Head Handle Screw
3. Remove door hinge hole plug from freezer door. Move to
opposite side hinge hole as shown below.
A. Door Hinge Hole Plug
4. Remove the brand badge using the plastic tool (provided).
Replace it with the badge provided in the Reversibility Kit
located inside the crisper drawer. For proper placement, see
the Brand Badge Placement template (the last page of this
manual).
NOTEs:
� To avoid scratching the finish, do not use a sharp or
metallic object to pry the brand badge from the door.
� Rub a small amount of liquid dish soap over any adhesive
residue with your fingers. Rinse the door with warm water
and dry with a soft cloth.
5.
A. Door stop screw B. Door stop
6. Remove door stop. Move to opposite side of refrigerator door
as shown.
7. Refer to image in Step 2. Position freezer handle on opposite
side of the freezer door. First, drive the bottom two screws into
handle. Align upper portion of handle and drive top screw into
handle.
8. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.
9. Replace screw cover. Refer to image in Step 2.
Refrigerator Door
1. Remove the screw cover.
2. Remove refrigerator handle assembly as shown below. Keep
all parts together..
A. Flat-Head Handle Screw C. Handle Screw
B. Refrigerator Handle D. Screw Cover