Dispensing Guide

ManualsBrandsWhirlpool ManualsFrench Door RefrigeratorsWRX986SIHZ

Table Of Contents

FFrreenncchh DDoooorr BBoottttoomm MMoouunntt DDiissppeennssiinngg aanndd SSttoorraaggee GGuuiiddee

Water and Ice Dispenser Controls

A. Ice/Water dispenser paddle

Press Ice/Water to toggle through the following choices in a

continuous loop:

� Water (default) - Dispenses water.

� Cubed - Dispenses cubed ice.

� Crushed - Dispenses crushed ice.

TO DISPENSE WATER (STANDARD)

1. Select water.

2. Press a sturdy glass against the water dispenser paddle.

NOTE: While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how much

water has been dispensed.

3. Remove the glass to stop dispensing.

TO DISPENSE WATER (MEASURED FILL)

Measured Fill allows you to dispense a specified amount of water

with the touch pad.

NOTE: The amount of water you select will be dispensed. Be sure

that the container is empty and can hold the entire volume. If ice is

in the container, you may need to adjust your selection.

Household water pressure may affect the accuracy of the

Measured Fill feature. For optimum performance of your water

dispenser, you must first calibrate Measured Fill. For best results,

calibration should be performed when water is not being used in

the house.

How to calibrate Measured Fill:

IMPORTANT: Flush the water system before calibrating Measured

Fill.

1. Place a sturdy measuring cup (1-cup [237 mL] size) on the

dispenser tray centered in front of the ice/water dispenser

paddle.

NOTE: Depending on your model, a measuring cup may be

provided.

2. Press and hold the Options and Lock buttons at the same time

for 3 seconds. The words “Back” and “1 Cup” will appear on the

display screen. Also, the Calibrate Measured Fill icon will

illuminate and remain lit while the Measured Fill feature is being

calibrated.

NOTE: You may press Ice Type “Back” at any time to exit

calibration mode. The Calibrate Measured Fill icon will disappear.

3. Press and release the water dispenser paddle, as needed, to

dispense water to the 1 cup fill line.

NOTE: If overfilling or spilling occurs, discard the water and

press “Back” to restart the calibration process.

4. Press Measured Fill to turn on the feature. When the feature is

on, the Measured Fill screen appears on the display.

When Measured Fill calibration has been confirmed, the

Calibration icon will disappear and the display will return to the

home screen.

1. Press Measured Fill to turn the feature on. When the feature is

on, the Measured Fill screen appears on the display. Press Ice/

Water “Back” to manually turn off the Measured Fill feature.

NOTE: The dispenser will automatically turn off Measured Fill

after 1 minute of inactivity. When Measured Fill is turned off,

any changes you have made will be lost and all defaults will be

restored.

2. You can dispense water by the ounce, cup, or liter. The default

unit is ounces. To switch to cups or liters, press the Light

button.

Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1/4 16

Liters 0.25 0.05 4.00

3. Press the Lock and Options buttons to adjust the volume as

desired. The Lock button increases the volume, and the

Options button lowers the volume.

NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]

per cup) are not the same size as a measuring cup (8 oz [237

mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

When increasing or decreasing the dispense volumes, if an

adjustment button (-/+) is held for approximately 10 seconds or

longer the control may stop responding. Release the button for

approximately 2 seconds and then continue making the

adjustment.

Summary of content (9 pages)

PAGE 1
French Door Bottom Mount Dispensing and Storage Guide Water and Ice Dispenser Controls NOTE: You may press Ice Type “Back” at any time to exit calibration mode. The Calibrate Measured Fill icon will disappear. A. Ice/Water dispenser paddle Press Ice/Water to toggle through the following choices in a continuous loop: 3. Press and release the water dispenser paddle, as needed, to dispense water to the 1 cup fill line.
PAGE 2
4. Dispense water. NOTE: While dispensing water, the digital display will count down how much water remains to be dispensed, according to the volume you selected. The flow of water will automatically stop once the desired volume has been dispensed. � Press a sturdy glass against the dispenser paddle. or � Place the glass below the water dispenser and press Measured Fill, under Dispense, for hands-free dispensing. 5.
PAGE 3
To remove EasySlide bin: 1. Remove all three crisper drawers. 2. Hold the upper sliding lid near the trim and lift up to remove. Remove the lower lid. 3. Grasp the front of the bin with both hands, and lift up on the front to remove. To replace EasySlide bin: 1. Slightly tilt the rear of the bin upward. 2. Align the center rib and tabs on the EasySlide bin with the ribs and slots in the cabinet. 3. Lower the bin into place.
PAGE 4
Guide de rangement et du distributeur du réfrigérateur à porte à double battant et congélateur au bas Commandes du distributeur d’eau et de glaçons Calibration du remplissage mesuré : IMPORTANT: Purger le circuit d’eau avant de calibrer le Measured Fill (remplissage mesuré). A. Plaque du distributeur à eau/glaçons Appuyer de nouveau sur Ice/Water (glaçons/eau) pour permuter entre les choix suivants (répétés en boucle) : � Water (eau) (par défaut) – Distribue de l’eau.
PAGE 5
2. Il est possible de puiser l’eau par once, par tasse ou par litre. L’unité utilisée par défaut est l’once. Pour passer aux tasses ou aux litres, appuyer sur le bouton Light (éclairage). Les volumes par défaut, minimum et maximum sont indiqués ci-dessous. Unités Par défaut Minimum Maximum Onces 8 1 128 Tasses 1 1/4 16 Litre 0,25 0,05 4,00 3. Appuyer sur les boutons Lock (verrouillage) et Options pour régler le volume comme désiré.
PAGE 6
Appuyer sur Select (sélectionner) pour alterner entre les différents réglages de température. L’icône s’allume lorsque le réglage souhaité est sélectionné. Pour replacer le bac EasySlide : 1. Incliner légèrement l’arrière du bac vers le haut. 2. Aligner l’arête centrale et les languettes du bac EasySlide avec les arêtes et encoches du cabinet. 3. Abaisser le bac pour le mettre en place.
PAGE 7
Guía de despacho y almacenamiento del refrigerador de dos puertas con montaje en la parte inferior Controles del despachador de agua y hielo Cómo calibrar Measured Fill (Llenado medido): IMPORTANTE: Enjuague el sistema de agua antes de calibrar la función Measured Fill (Llenado medido). A. Palanca del despachador de hielo/agua Presione Ice/Water (Hielo/Agua) para ver las siguientes opciones en un bucle continuo: 1.
PAGE 8
2. Puede despachar agua por onza, taza o litro. La unidad prefijada es onzas. Para cambiar a tazas o litros, presione el botón Light (Luz). A continuación se enlistan los volúmenes prefijados, mínimos y máximos. Unidades Predeterminado Mínimo Máximo Onzas 8 1 128 Tazas 1 1/4 16 Litros 0,25 0,05 4,00 3. Presione los botones de Lock (Bloquear) o de Options (Opciones) para ajustar el volumen que desea.
PAGE 9
Cajón para verduras y tapa Funciones adicionales del panel de control Para quitar la tapa de los cajones para verduras: 1. Retire los cajones para verduras. 2. Sostenga la pieza de vidrio firmemente con una mano y presione hacia arriba en el centro de la pieza de vidrio hasta que se levante por encima del marco de plástico. Deslice con cuidado la pieza de vidrio hacia adelante para retirarla. 3. Levante el marco de la tapa y sáquela.