36" (91.4 CM) ISLAND-MOUNT CANOPY RANGE HOOD Installation Instructions and Use & Care Guide For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301 or visit our website at www.whirlpool.com In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.
TABLE OF CONTENTS TABLE DES MATIÈRES RANGE HOOD SAFETY..................................................................2 INSTALLATION REQUIREMENTS..................................................4 Tools and Parts..............................................................................4 Location Requirements.................................................................4 Venting Requirements...................................................................5 Electrical Requirements................
IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS 3
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■■ T10 Torx®† adapter ■■ T20®† Torx® adapter ■■ 2 - Upper vent covers ■■ 2 - Lower vent covers ■■ 4 - Plastic vent clips ■■ Mounting template ■■ Level ■■ Drill with 1 /4" (3.2 cm), /8" (9.5 mm), /8" (3.2 mm), and 7/64" (2.
The chimneys can be adjusted for different ceiling heights. See the following chart. Product Dimensions A B Vented Installations C Max. ceiling height 7' 8" (2.34 m) 9' 10" (3 m) Gas cooking surface 7' 11" (2.41 m) 9' 10" (3 m) Non-Vented (Recirculating) Installations D F Min. ceiling height Electric cooking surface E A. 12 / " (31.1 cm) B. 133/16" (33.5 cm) C. *293/4" (75.6 cm) min. 4413/16" (113.8 cm) max. **293/4" (75.6 cm) min. 4913/16" (126.5 cm) max. D. 31/2" (8.9 cm) E. 36" (91.
Makeup Air Example Vent System Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. 90 elbow 6 ft (1.8 m) 2 ft (0.6 m) Venting Methods This island hood is factory set for venting through the roof. A 6" (15.2 cm) round vent system is needed for installation (not included).
INSTALLATION INSTRUCTIONS Prepare Location ■■ Lay out the vent duct system before installing the range hood to determine the best routing for the vent duct. ■■ It is recommended that the vent system be installed before the range hood is installed. ■■ Before making cutouts, make sure there is proper clearance within the ceiling for exhaust vent. ■■ Range hood is to be installed 24" (61 cm) min. for electric cooking surfaces, 27" (68.6 cm) min.
Install In-Line Smart Kit - Optional A NOTE: Your range hood can work with either an internal or an inline (external) blower motor system. An optional In-Line Smart Kit (purchased separately) allows the blower motor that comes with this range hood to be installed in a location other than inside the range hood cavity. CAUTION: To reduce the risk of fire and electric shock, install this range hood only with the In-Line Smart Kit manufactured by Whirlpool, Part Number W10692945.
Make Electrical Connection 4. Run home power supply cable through strain relief into terminal box. WARNING A B C Electrical Shock Hazard Disconnect power before servicing. D Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Disconnect power. 2. Remove terminal box cover. 3. Remove the knockout in the terminal box and install a UL listed or CSA approved 1/2" strain relief. A B C E A. Home power supply cable B.
Install Duct Covers NOTE: Remove the film from the duct covers. 1. Assemble the upper duct covers together and install the duct covers around the support frame. The larger hole in the flanges of the upper duct cover must be outside the smaller hole in the mating flange of the other upper duct cover. 2. Secure the upper duct covers together with two 3.5 x 6.5 mm screws at the top and two 2.9 x 3 mm screws at the bottom. Install 1 screw on each side at the top and bottom of the assembled duct covers. 3.
6. Install the lower duct cover (rear) to the range hood canopy. Spread the lower duct cover opening slightly and position it over the upper duct cover. Set the lower duct cover in place. Position so the flanges of the lower duct cover set into the flanges of the upper duct cover. Make sure the front and rear lower duct covers mate properly.
RANGE HOOD USE The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen. The hood controls are located on the front side of the canopy. Range Hood Controls A A. B. C. D. E.
RANGE HOOD CARE Cleaning IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filters before operating hood. Exterior Surfaces To avoid damage to the exterior surface, do not use steel wool or soap-filled scouring pads. Always wipe dry to avoid water marks. Cleaning Method: ■■ Liquid detergent soap and water, or all-purpose cleanser. ■■ Wipe with damp soft cloth or nonabrasive sponge, and then rinse with clean water and wipe dry.
WIRING DIAGRAM Ambient Light Switch Function Position BK 1 2 1 3 2 1 Push Button Switch 3 1 RD BK G 2 L La M (M - La) BU 2 3 YL/GN N WH L 3 YL Position 2 Position 1 BR Position 3 Off Auto WH On Push Button Switch Operation Function Position Off No Connection Blue - Yellow Lamps Low Speed Brown - White Med Speed Brown - Red High Speed Brown - Black (L - 1) (L - 2) (L - 3) BU BU BU RD BU Strip LED RD BK RD RD BK RD Strip LED BK 14 WH YL 8 9 YL BR YL/GN 4
ASSISTANCE OR SERVICE In Canada If you need service Please refer to the warranty page in this manual. If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new appliance.
WHIRLPOOL® MAJOR APPLIANCE LIMITED WARRANTY ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. Please have the following information available when you call the Customer eXperience Center: ■■ Name, address and telephone number ■■ Model number and serial number ■■ A clear, detailed description of the problem ■■ Proof of purchase including dealer or retailer name and address IF YOU NEED SERVICE: 1.