Instructions for use WASHING MACHINE Contents GB Installation, 2-3-4-5 AR English,1 GB , 15 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 6 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 7 General safety Load balancing system Disposal XWA
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
GB As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
Technical data Model Dimensions Capacity Electrical connections Water connections GB XWA 71251 width 59.5 cm height 85 cm depth 54 cm from 1 to 7 kg please refer to the technical data plate fixed to the machine maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres Spin speed up to 1200 rotations per minute Test Programmes according to SASO 2692.2007/2693.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Unplug the washing machine when cleaning it and during all maintenance work. Cleaning the washing machine • The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washing machine and starting a wash cycle GB Control panel WASH CYCLE PROGRESS indicator lights ON/OFF button Detergent dispenser drawer knob PUSH & WASH button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
Indicator lights The indicator lights provide important information. This is what they can tell you: Delayed start If the DELAY TIMER function has been activated (see “Personalisation”), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash: Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash cycles Push & Wash This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds. The lit indicator light indicates that the cycle has started.
Personalisation Setting the temperature GB Press the TEMPERATURE button to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash . The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle. ! Exception: if the 8 programme is selected, the temperature can be increased up to a value of 90°C.
Detergents and laundry GB Detergent dispenser drawer Successful washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. ! Do not use hand washing detergents because these create too much foam. ! Use powder detergent for white cotton garments, for prewashing, and for washing at temperatures over 60°C.
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • • The washing machine door is not closed properly.
Service GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
تعليمات االستخدام ماكينة غسيل المحتويات عربي عربي، عربي التركيب16-17-18-19 ، إفراغ المحتويات وتحديد المستوى وصل إمدادات الكهرباء والماء دورة الغسيل األولى البيانات التقنية العناية والصيانة20 ، قطع إمداد الماء أو الكهرباء تنظيف ماكينة الغسيل تنظيف درج وعاء مواد التنظيف العناية بباب وبرميل الجهاز لديك ّ المضخة تنظيف فحص خرطوم إدخال الماء وسائل حذر ونصائح21 ، الوقاية العامة نظام موازنة الحمل التخلص XWA 71251 وصف ماكينة الغسيل وتشغيل دورة ال
التركيب عربي ! يجب االحتفاظ بدليل التعليمات هذا في مكان آمن لمراجعته في المستقبل .إذا تم بيع الجهاز ،إرساله أو نقله، تأكد من أن دليل التعليمات قد أرفق بالماكينة بحيث يتمكن مالكوها الجدد من التعرف على عملها وخصائصها. ! اقرأ هذه التعليمات بعناية :إنها تحتوي على معلومات هامة فيما يتعلق بالتركيب اآلمن وتشغيل الجهاز. إفراغ المحتويات وتحديد المستوى إفراغ المحتويات .1أخرج ماكينة الغسيل من رزمتها. .
وصل خرطوم تصريف الماء قم بتوصيل خرطوم تصريف الماء ،من دون ثنيه ،بأنبوب تصريف أو بتصريف جداري على ارتفاع يتراوح بين 65 وحتى 100سم عن األرض؛ مؤرضا. تحذير -يجب أن يكون هذا الجهاز ّ يجب تنفيذ العمليات التالية من قبل أخصائي كهرباء مؤهل. 65 - 100 cm أو قم بتثبيته على طرف الحوض أو المغسلة ،مع تثبيت األنبوب المز ّود بالحنفية (أنظر الرسم). على الطرف الحر من الخرطوم أال يكون تحت الماء.
عربي في حال لم تتوافق ألوان األسالك في التوصيل مع مفاتيح األلوان المعرفة في أطراف القابس لديك ،تصرف على النحو التالي: قم بتوصيل السلك األخضر واألصفر بالنهائية المشار إليها بـ Eأو باللون األخضر أو األخضر واألصفر. قم بتوصيل السلك البني بالنهائية المشار إليها بـ Lأو الملونة باللون األحمر. قم بتوصيل السلك األزرق بالنهائية المشار إليها بـ Nأو الملونة باللون األسود.
البيانات التقنية الطراز األبعاد السعة التوصيالت الكهربائية الماء عربي XWA 71251 العرض 59.5سم االرتفاع 85سم العمق 54سم من 1إلى 7كجم يُرجى الرجوع إلى لوحة البيانات المثبتة على الجهاز الحد األقصى للضغط 1ميجا باسكال ( 10بار) الحد األدنى للضغط 0.05ميجا باسكال ( 0.5بار) سعة البرميل 52لتر سرعة العصر ما يصل إلى 1200دورة في الدقيقة تم اختبار البرامج تبعاً للمعايير SASO 2692.2007/2693.
العناية والصيانة عربي قطع إمداد الماء والكهرباء ّ المضخة تنظيف • قم بإقفال حنفية الماء بعد كل دورة غسيل .سيحد هذا من تآكل النظام الهيدروليكي داخل ماكينة الغسيل ويساعد على منع التسربات. • افصل الماكينة عن الكهرباء عند تنظيفها أو أثناء أي عمل صيانة. ماكينة الغسيل مزودة بمضخة للتنظيف الذاتي ،حيث ال تحتاج إلى أية عناية في أي وقت .
وسائل حذر ونصائح ! تم تصميم ماكينة الغسيل وتصنيعه طبقا لمواصفات األمان العالمية .يتم تزويد التحذيرات التالية ألسباب وقائية ويجب قراءتها بعناية. الوقاية العامة • • • • • • • • • • • • • تم تصميم هذا الجهاز لالستخدام المنزلي فقط.
وصف ماكينة الغسيل وتشغيل دورة الغسيل عربي لوحة التحكم لعملية دورة الغسيل الوظيفة أزرار مع مصابيح مؤشرة مصابيح مؤشرة الباب مقفل START/PAUSE زر ومؤشر مؤشر عداد الوقت المؤجل درجة الحرارة زر زر العصر زر درج وعاء مواد التنظيف:يتم استخدامه لتوزيع مواد التنظيف ومضافات الغسيل (انظر "مواد التظيف والغسيل"). تشغيل/إيقاف تشغيل زر :لتشغيل ماكينة الغسيل وإيقاف تشغيلها. زر الدفع والغسل( :أنظر "دورات الغسيل والوظائف").
المؤشرات فور اختيار دورة الغسيل المرغوب بها وبدءها ،تضيئ المصابيح المؤشرة ،الواحد تلو اآلخر لإلشارة إلى الدورة التي تعمل حاليا. عربي توفر المؤشرات معلومات هامة .
دورات الغسيل عربي Push & Wash تسمح هذه الوظيفة ببدء دورة غسل حتى بعد إيقاف تشغيل الجهاز دون الحاجة للضغط على الزر "تشغيل/إيقاف" مقدماً ،أو بعد تشغيل الجهاز، دون تنشيط أي زر و/أو مفتاح (عدا ذلك ،سيتم إلغاء تنشيط وظيفة "دفع وغسل") .لبدء دورة "دفع وغسل" ،اضغط مع االستمرار على الزر المناسب لمدة ثانيتين .يشير مصباح المؤشر المضيء إلى أن الدورة قد بدأت .
التخصيصات ضبط درجة الحرارة اضغط على مفتاح درجة الحرارة لضبط درجة حرارة الغسيل (انظرجدول دورات الغسيل). يمكن خفض درجة الحرارة أو حتى إعدادها للغسيل البارد .ستمنعك ماكينة الغسيل أوتوماتيكيا من اختيار درجة حرارة أعلى من القيمة القصوى المحددة لكل دورة غسيل. ! استثناء :إذا تم اختيار البرنامج ،8فمن الممكن زيادة درجة الحرارة حتى 90درجة مئوية. ضبط سرعة الدوران اضغط مفتاح سرعة الدوران لضبط سرعة العصر لدورة الغسيل المختارة.
مواد التنظيف والغسيل عربي درج وعاء مواد التنظيف تعتمد نتائج الغسيل الناجحة أيضا على كمية مواد التنظيف :إن إضافة مواد تنظيف أكثر مما يجب ال يزيد فاعلية الغسيل بالضرورة ،يمكن أن يؤدي إلى انسداد في األجزاء الداخلية من الجهاز لديك وحتى يمكن أن يلوث البيئة. ! ال تستخدم المواد المعدة للغسيل باليد ألنها يمكن أن تطلق رغوة فائضة. ! استخدام مواد التنظيف على شكل مسحوق للمالبس القطنية البيضاء ،لمرحلة ما قبل الغسيل ،وللغسيل في درجات حرارة أعلى من 60مئوية.
استكشاف المشاكل وحلها يمكن لماكينة الغسيل أن تفشل في العمل فجأة .قبل االتصال بمركز المساعدة التقنية (أنظر "الخدمة") تأكد من أن المشكلة ال يمكن حلها بسهولة باستخدام الجدول التالي. المشكلة: األسباب المحتملة /الحلول: ال يمكن تشغيل ماكينة الغسيل. • الجهاز غير موصل بالمقبس الكهربائي بشكل كامل ،أو أنه ال يحدث تماس. • يوجد انقطاع كهرباء في البيت. عربي دورة الغسيل ال تبدأ بالعمل. • • • • • باب ماكينة الغسيل غير مقفل بشكل صحيح.
الخدمة 195127744.01 12/2014 - Xerox Fabriano عربي قبل االتصال بخدمة المساعدة التقنية: • افحص فيما إذا كان بإمكانك حل المشكلة بنفسك(أنظر " استكشاف المشاكل وحلها"). • أعد تشغيل دورة الغسيل للفحص فيما إذا تم حل المشكلة. • إذا لم يحدث ذلك ،اتصل بمركز مساعدة تقنية معتمد. ! اطلب دائما مساعدة فنّي مؤهل. الرجاء خذ بعين االعتبار المعلومات التالية: • نوع المشكلة؛ • طراز الجهاز ()Mod.؛ • الرقم التسلسلي (.