Instructions for use WASHING MACHINE Contents FR GB English,1 Français,13 IT Italiano,25 GB Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 4 ES Español,37 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 5 General safety Loa
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drain duct or a wall drain situated between 65 and 100 cm from the floor; ! Do not use extension cords or multiple sockets. ! The cable should not be bent or compressed. ! The power supply cable must only be replaced by authorised technicians. Warning! The company shall not be held responsible in the event that these standards are not observed.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Unplug the washing machine when cleaning it and during all maintenance work. Cleaning the washing machine • The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washing machine and starting a wash cycle GB Control panel WASH CYCLE PROGRESS indicator lights ON/OFF button Detergent dispenser drawer SPIN SPEED knob Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). ON/OFF button: switches the washing machine on and off. PUSH & WASH button: (see “Wash cycles”). WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.
Indicator lights The indicator lights provide important information. This is what they can tell you: Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash cycles Push & Wash This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds. The lit indicator light indicates that the cycle has started.
Personalisation Setting the temperature Turning the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash . N.B.: If the set value is compatible with the selected cycle, the knob indicator will be lit (fixed light). If it isn’t, it will flash and 3 beeps will be heard. The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle.
Detergents and laundry GB Detergent dispenser drawer Successful washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. ! Do not use hand washing detergents because these create too much foam. ! Use powder detergent for white cotton garments, for prewashing, and for washing at temperatures over 60°C.
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • The washing machine door is not closed properly.
Service GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Mode d’emploi LAVE-LINGE Sommaire FR Français FR Installation, 14-15 Déballage et mise à niveau Raccordements eau et électricité Premier cycle de lavage Caractéristiques techniques Entretien et soin, 16 Coupure de l’arrivée d’eau et du courant Nettoyage du lave-linge Nettoyage du tiroir à produits lessiviels Entretien du hublot et du tambour Nettoyage de la pompe Contrôle du tuyau d’arrivée de l’eau Précautions et conseils, 17 XWC 81251 Sécurité générale Système d’équilibrage de la charge Mise au rebu
Installation FR ! Conserver ce mode d’emploi pour pouvoir le consulter à tout moment. En cas de vente, de cession ou de déménagement, veiller à ce qu’il suive toujours le lave-linge pour que son nouveau propriétaire soit informé sur son mode de optionnement et puisse profiter des conseils correspondants. ! Lire attentivement les instructions: elles fournissent des conseils importants sur l’installation, l’utilisation et la sécurité de l’appareil. Déballage et mise à niveau Déballage 1.
Raccordement du tuyau de vidange 65 - 100 cm Raccorder le tuyau d’évacuation, sans le plier, à un conduit d’évacuation ou à une évacuation murale placés à une distance du sol comprise entre 65 et 100 cm ; ou bien l’accrocher à un évier ou à une baignoire, dans ce cas, fixer le support en plastique fourni avec l’appareil au robinet (voir figure). L’extrémité libre du tuyau d’évacuation ne doit pas être plongée dans l’eau.
Entretien et soin FR Coupure de l’arrivée d’eau et du courant • Fermer le robinet de l’eau après chaque lavage. Cela réduit l’usure de l’installation hydraulique du lave-linge et évite tout danger de fuites. • Débrancher la fiche de la prise de courant lors de tout nettoyage du lave-linge et pendant tous les travaux d’entretien. Nettoyage du lave-linge • Pour nettoyer l’extérieur et les parties en caoutchouc, utiliser un chiffon imbibé d’eau tiède et de savon. N’utiliser ni solvants ni abrasifs.
Précautions et conseils ! Ce lave-linge a été conçu et fabriqué conformément aux normes internationales de sécurité. Ces consignes sont fournies pour des raisons de sécurité, il faut les lire attentivement. Sécurité générale • Cet appareil est conçu pour un usage domestique.
Description du lave-linge et démarrage d’un programme FR Bandeau de commandes Voyants DÉROULEMENT CYCLE Touche ON/OFF Tiroir à produits lessiviels HUBLOT VERROUILLÉ START/PAUSE Bouton et voyant Bouton ESSORAGE PROGRAMMES PUSH & WASH Tiroir à produits lessiviels: pour charger les produits lessiviels et les additifs (voir “Produits lessiviels et linge”). Touche ON/OFF: pour allumer ou éteindre le lave-linge. Touche PUSH & WASH: (voir “Programmes”).
Voyants Les voyants fournissent des informations importantes. Voilà ce qu’ils signalent: Voyants phase en cours Une fois que le cycle de lavage sélectionné a démarré, les voyants s’allument progressivement pour indiquer son stade d’avancement: Voyant hublot verrouillé Le voyant allumé indique que le hublot est verrouillé pour en empêcher l’ouverture. Attendre que le voyant cesse de clignoter avant d’ouvrir la porte (3 minutes environ).
Programmes Push & Wash Cette fonction permet de lancer un cycle de lavage même si la machine est éteinte sans qu’il faille préalablement appuyer sur la touche ON/OFF ou, après allumage de la machine, sans avoir besoin d’activer aucune autre touche et/ou bouton (autrement le programme Push & Wash sera désactivé). Pour lancer le cycle Push & Wash appuyer 2 secondes de suite sur la touche. L’allumage du voyant signale que le cycle est lancé.
Personnalisations Sélection de la température Tourner le bouton TEMPÉRATURE pour sélectionner la température de lavage (voir Tableau des programmes). La température peut être abaissée jusqu’au lavage à froid ( ). N.B.: si la valeur sélectionnée est compatible avec le programme sélectionné, le voyant du bouton s’allume en fixe, autrement il se met à clignoter et un signal sonore retentit (3 bips).
Produits lessiviels et linge FR Tiroir à produits lessiviels Un bon résultat de lavage dépend aussi d’un bon dosage de produit lessiviel : un excès de lessive ne lave pas mieux, il incruste l’intérieur du lave-linge et pollue l’environnement. ! Ne pas utiliser de lessives pour lavage à la main, elles moussent trop. ! Utiliser des lessives en poudre pour du linge en coton blanc et en cas de prélavage et de lavages à une température supérieure à 60°C.
Anomalies et remèdes Il peut arriver que le lave-linge ne optionne pas bien. Avant d’appeler le Service de dépannage (voir “Assistance”), contrôler s’il ne s’agit pas par hasard d’un problème facile à résoudre à l’aide de la liste suivante. FR Anomalies: Causes / Solutions possibles: Le lave-linge ne s’allume pas. • La fiche n’est pas branchée dans la prise de courant ou mal branchée. • Il y a une panne de courant. Le cycle de lavage ne démarre pas. • • • • Le hublot n’est pas bien fermé.
Assistance FR Avant d’appeler le service après-vente: • Vérifier si on ne peut pas résoudre l’anomalie par ses propres moyens (voir “Anomalies et Remèdes”); • Remettre le programme en marche pour contrôler si l’inconvénient a disparu; • Autrement, contacter le Centre d’Assistance technique agréé au numéro de téléphone indiqué sur le certificat de garantie. ! Ne jamais s’adresser à des techniciens non agréés. Communiquer: • le type de panne; • le modèle de l’appareil (Mod.); • son numéro de série (S/N).
Istruzioni per l’uso LAVABIANCHERIA Sommario IT Italiano IT Installazione, 26-27 Disimballo e livellamento Collegamenti idraulici ed elettrici Primo ciclo di lavaggio Dati tecnici Manutenzione e cura, 28 Escludere acqua e corrente elettrica Pulire la lavabiancheria Pulire il cassetto dei detersivi Curare oblò e cestello Pulire la pompa Controllare il tubo di alimentazione dell’acqua Precauzioni e consigli, 29 XWC 81251 Sicurezza generale Sistema bilanciamento del carico Smaltimento Descrizione della
Installazione IT ! È importante conservare questo libretto per poterlo consultare in ogni momento. In caso di vendita, di cessione o di trasloco, assicurarsi che resti insieme alla lavabiancheria per informare il nuovo proprietario sul funzionamento e sui relativi avvertimenti. Un accurato livellamento dà stabilità alla macchina ed evita vibrazioni, rumori e spostamenti durante il funzionamento.
Collegamento del tubo di scarico 65 - 100 cm Collegare il tubo di scarico, senza piegarlo, a una conduttura di scarico o a uno scarico a muro posti tra 65 e 100 cm da terra; oppure appoggiarlo al bordo di un lavandino o di una vasca, legando la guida in dotazione al rubinetto (vedi figura). L’estremità libera del tubo di scarico non deve rimanere immersa nell’acqua.
Manutenzione e cura IT Escludere acqua e corrente elettrica Pulire la pompa Pulire la lavabiancheria ! Assicurarsi che il ciclo di lavaggio sia terminato e staccare la spina. Per accedere alla precamera: 1. rimuovere il pannello di copertura sul lato anteriore della 1 macchina premendo verso il centro, quindi spingere verso il 2 3 basso da entrambe i lati ed estrarlo (vedi figure). • Chiudere il rubinetto dell’acqua dopo ogni lavaggio.
Precauzioni e consigli ! La lavabiancheria è stata progettata e costruita in conformità alle norme internazionali di sicurezza. Queste avvertenze sono fornite per ragioni di sicurezza e devono essere lette attentamente. Sicurezza generale • Questo apparecchio è stato concepito esclusivamente per un uso di tipo domestico.
Descrizione della lavabiancheria e avviare un programma IT Pannello di controllo SPIE AVANZAMENTO CICLO Tasto ON/OFF Cassetto dei detersivi START/PAUSE MANOPOLA PROGRAMMI Tasto PUSH & WASH Cassetto dei detersivi: per caricare detersivi e additivi (vedi “Detersivi e biancheria”). Tasto ON/OFF: per accendere e spegnere la lavabiancheria. Tasto PUSH & WASH: (vedi “Programmi”). Manopola PROGRAMMI: per impostare i programmi. Durante il programma la manopola resterà ferma.
Spie Le spie forniscono informazioni importanti. Ecco che cosa dicono: Spie fase in corso Una volta selezionato e avviato il ciclo di lavaggio desiderato, le spie si accenderanno progressivamente per indicarne lo stato di avanzamento. Lavaggio Spia oblò bloccato La spia accesa indica che l’oblò è bloccato per impedire l’apertura; per aprire l’oblò è necessario che la spia sia spenta (attendere 3 minuti circa).
Programmi Push & Wash Questa funzione permette di avviare un ciclo di lavaggio anche a macchina spenta senza dover preventivamente premere il tasto ON/OFF o, successivamente all’accensione della macchina, senza aver azionato nessun ulteriore tasto e/o manopola (diversamente il programma Push & Wash sarà disattivato). Per avviare il ciclo Push & Wash tenere premuto il pulsante per 2 secondi. La spia accesa indica che il ciclo è avviato.
Personalizzazioni Impostare la temperatura Ruotando la manopola TEMPERATURA si imposta la temperatura di lavaggio (vedi Tabella programmi). La temperatura si può ridurre sino al lavaggio a freddo . N.B.: se il valore impostato è compatibile con il programma selezionato, la spia della manopola sarà accesa fissa, altrimenti lampeggerà e si avrà un segnale acustico (3 beep) La macchina impedirà automaticamente di impostare una temperatura maggiore a quella massima prevista per ogni programma.
Detersivi e biancheria IT Cassetto dei detersivi Il buon risultato del lavaggio dipende anche dal corretto dosaggio del detersivo: eccedendo non si lava in modo più efficace e si contribuisce a incrostare le parti interne della lavabiancheria e a inquinare l’ambiente. ! Non usare detersivi per il lavaggio a mano, perché formano troppa schiuma. ! Usare detersivi in polvere per capi in cotone bianchi e per il prelavaggio e per lavaggi con temperatura superiore a 60°C.
Anomalie e rimedi Può accadere che la lavabiancheria non funzioni. Prima di telefonare all’Assistenza (vedi “Assistenza”), controllare che non si tratti di un problema facilmente risolvibile aiutandosi con il seguente elenco. Anomalie: Possibili cause / Soluzione: La lavabiancheria non si accende. • La spina non è inserita nella presa della corrente, o non abbastanza da fare contatto. • In casa non c’è corrente. Il ciclo di lavaggio non inizia. • • • • L’oblò non è ben chiuso.
Assistenza IT Prima di contattare l’Assistenza: • Verificare se l’anomalia può essere risolta da soli (vedi “Anomalie e rimedi”). • Riavviare il programma per controllare se l’inconveniente è stato ovviato; • In caso negativo, contattare il Numero Unico 199.199.199*. ! Non ricorrere mai a tecnici non autorizzati. Comunicare: • il tipo di anomalia; • il modello della macchina (Mod.); • il numero di serie (S/N).
Manual de instrucciones LAVADORA Sumario ES Español ES Instalación, 38-39 Desembalaje y nivelación Conexiones hidráulicas y eléctricas Primer ciclo de lavado Datos técnicos Mantenimiento y cuidados, 40 Interrumpir el agua y la corriente eléctrica Limpiar la lavadora Limpiar el cajón de detergentes Cuidar la puerta y el cesto Limpiar la bomba Controlar el tubo de alimentación de agua Precauciones y consejos, 41 XWC 81251 Seguridad general Sistema de equilibrado de la carga Eliminaciones Descripción de
Instalación ES ! Es importante conservar este manual para poder consultarlo en cualquier momento. En caso de venta, de cesión o de traslado, verifique que permanezca junto con la lavadora para informar al nuevo propietario sobre el funcionamiento y brindar las correspondientes advertencias. ! Lea atentamente las instrucciones: ellas contienen importante información sobre la instalación, el uso y la seguridad. Desembalaje y nivelación Desembalaje 1. Desembale la lavadora. 2.
Conexión del tubo de desagüe 65 - 100 cm Conecte el tubo de desagüe, sin plegarlo, a un conducto de desagüe o a una desagüe de pared ubicados a una distancia del piso comprendida entre 65 y 100 cm.; o apóyelo en el borde de un lavamanos o de una bañera, uniendo la guía suministrada con el aparato, al grifo (ver la figura). El extremo libre del tubo de desagüe no debe permanecer sumergido en el agua.
Mantenimiento y cuidados ES Interrumpir el agua y la corriente eléctrica • Cierre el grifo de agua después de cada lavado. De este modo se limita el desgaste de la instalación hidráulica de la lavadora y se elimina el peligro de pérdidas. • Desenchufe la máquina cuando la debe limpiar y durante los trabajos de mantenimiento. Limpiar la lavadora • La parte externa y las partes de goma se pueden limpiar con un paño embebido en agua tibia y jabón. No use solventes ni productos abrasivos.
Precauciones y consejos ! La lavadora fue proyectada y fabricada en conformidad con las normas internacionales de seguridad. Estas advertencias se suministran por razones de seguridad y deben ser leídas atentamente. Seguridad general • Este aparato ha sido fabricado para un uso de tipo doméstico exclusivamente.
Descripción de la lavadora y comienzo de un programa ES Panel de control Pilotos DE AVANCE DEL CICLO Botones con pilotos FUNCIÓN Botón ON/OFF Contenedor de detergentes BLOQUEADA START/PAUSE Mando de Mando con piloto PROGRAMAS Botón PUSH & WASH Contenedor de detergentes: para cargar detergentes y aditivos (ver “Detergentes y ropa”). Botón de ON/OFF: para encender y apagar la lavadora. Botón PUSH & WASH: (ver “Programas”). Mando de PROGRAMAS: para elegir los programas.
Pilotos Los pilotos suministran información importante. He aquí lo que nos dicen:. Pilotos fase en curso Una vez seleccionado y puesto en marcha el ciclo de lavado deseado, las luces testigo se encenderán progresivamente para indicar su estado de avance: Piloto puerta bloqueada El piloto encendido indica que la puerta está bloqueada impidiendo su apertura; para poder abrir la puerta es necesario que dicho piloto esté apagado (espere 3 minutos aproximadamente).
Programas Push & Wash Esta función permite poner en marcha un ciclo de lavado incluso con la máquina apagada sin tener que presionar anteriormente el botón ON/OFF o, después de encender la máquina, sin accionar ningún otro botón y/o mando (de lo contrario el programa Push & Wash será desactivado). Para poner en marcha el ciclo Push & Wash mantenga presionado el botón durante 2 segundos. El piloto encendido indica que el ciclo está en marcha.
Personalizaciones Seleccionar la temperatura ES Girando el mando TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas). La temperatura se puede disminuir hasta el lavado en frío ( ). Nota: si el valor programado es compatible con el programa seleccionado, el piloto de la perilla permancerá encendido fijo, de lo contrario, parpadeará y aparecerá una señal acústica (bip). La máquina impedirá automáticamente seleccionar una temperatura mayor que la máxima prevista para cada programa.
Detergentes y ropa ES Contenedor de detergentes El buen resultado del lavado depende también de la correcta dosificación del detergente: si se excede la cantidad, no se lava de manera más eficaz, sino que se contribuye a encostrar las partes internas de la lavadora y a contaminar el medio ambiente. ! No use detergentes para el lavado a mano porque producen demasiada espuma. ! Utilice detergentes en polvo para prendas de algodón blancas, para el prelavado y para lavados con una temperatura mayor que 60ºC.
Anomalías y soluciones Puede suceder que la lavadora no funcione. Antes de llamar al Servicio de Asistencia Técnica (ver “Asistencia”),controle que no se trate de un problema de fácil solución utilizando la siguiente lista. Anomalías: Posibles causas / Solución: La lavadora no se enciende. • El enchufe no está introducido en la toma de corriente, o no hace contacto. • En la casa no hay corriente. El ciclo de lavado no comienza. • • • • La puerta no está correctamente cerrada.
Asistencia 195120069.01 02/2014 - Xerox Fabriano ES Antes de llamar al Servicio de Asistencia Técnica: • Verifique si la anomalía la puede resolver Ud. solo (ver “Anomalías y soluciones”); • Vuelva a poner en marcha el programa para controlar si el inconveniente fue resuelto; • Si no es así, llame al Servicio de Asistencia técnica autorizado, al número de teléfono indicado en el certificado de garantía. ! No recurra nunca a técnicos no autorizados.