Installation guide

ManualsBrandsWhirlpool ManualsRangeOfficial Whirlpool gas freestanding range

installation instructions

" r30 Fee

9758661

ing Sealed Burner GasBan e

with self-cleaning oven

Tip Over Hazard

A child or adult can tip the range and

be killed.

Connect anti-tip bracket to rear

range foot.

Reconnect the anti=tip bracket, if the

range is moved.

Failure to follow these instructions can

result in death or serious burns to

children and adults.

ii_ i ii

iil _i

_i iiiiiiiiiiiiiiiii

Quick Reference

Table of Contents:

_ges

[]

_-_

[]

Before you start

Electrical requirements

Gas supply requirements

Product dimensions

Cabinet dimensions/requirements

Installation steps

Gas conversions

if range does not operate

if you need assistance/service

Moving the range

iMPORTANT:

Read and savethese instructions.

iMPORTANT:

Installer: Leave Installation

Instructions with the homeowner.

Homeowner: Keep Installation

Instructions for future reference.

Read and save these instructions

for local electrical inspector's use.

Write down the model and serial

numbers before installing range.

Both numbers are listed on the

model/serial rating plate located on the

oven frame behind the storage drawer

panel.

Model #

Serial #

www.whirlpool.com

Part No. 9758661

Summary of content (12 pages)

PAGE 1
installation instructions 9758661 30" Fee r ing Sealed Burner Gas Ban e with self-cleaning oven \ \ Quick Reference Table of Contents: _ges Tip Over A child or adult be killed. Connect anti-tip range foot. Hazard can tip the range bracket Reconnect the anti=tip range is moved.
PAGE 2
Before you start... Your safety and the safety others are very important. of We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING.
PAGE 3
Tools needed: Parts supplied: Not shown: literature pack orifice spuds Ol Assemble the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. level flat-blade floor-mounted anti-tip bracket Materials needed: valve • 1/2" male pipe thread to pressure regulator • L.R gas-resistant nipple pipe-joint for connection compound • AGA or CSA design-certified flexible metal appliance connector (4-5 feet) (1.2-1.
PAGE 4
Gas supply requirements Observe all governing ordinances. codes and This installation must codes and ordinances. conform with local In the absence of connection: local codes, installations must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 -latest latest Explosion Hazard Use a new AGA or CSA approved supply line, Install a shutoff valve. Securely tighten gas all gas connections.
PAGE 5
Product dimensions Grounded electrical outlet is required. See "Electrical requirements:' Proper gas supply connection must be available. See "Gas supply requirements:' i l: 27-1/8" (68.9 cm) J depth with handle 36" (91.4 cm) cooktop height 46-7/8" (119.1 era) overall height 25" (63.5 cm) 29-7/8" (75.9 cm) width \ Cabinet dimensions/requirements J Anti-tip bracket The floor-mounted anti-tip bracket must be installed.
PAGE 6
Now start... Excessive Weight Use two or more install range. Failure other 1[] people Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type floor covering. Hazard to move in back or injury. Anti-tip securely Do not use oven door handle to lift or move the range. [] Remove to install shipping materials, and protective film from range. cardboard bottom and shipping under range to prevent damage covering.
PAGE 7
Gas and electrical connections m Apply pipe-joint for use with LR compound gas to the Om made smaller thread ends of the flexible connector adapters. Attach one adapter to the pressure regulator elbow and the other adapter to the gas shutoff valve.Tighten both and Use 5/16" channel combination lock pliers wrench to attach the flexible connector to the adapters. that connector is not kinked. Check show a leak. If a leak appears, shut gas supply valve and tighten connections.
PAGE 8
Check operation Electronic ignition system Cooktop and oven burners use electronic ignitors in place of standing pilots. When a cooktop control knob is turned to the "LIGHT" position, the system creates a spark to light the burner.This sparking continues until the control knob is turned to the desired setting. When the oven control is set to the desired setting, a series of sparks lights the oven burner.The sparking will stop when burner gas lights.
PAGE 9
if your oven has electronic controls: 1. Press the "BAKE" If oven flame needs to be adjusted: Locate the air shutter next to the pad. • Depending on model, the "BAKE" and "TEMP" indicators will light and "350" will appear in the display, or the "BAKE" indicator will light and "350" will appear in the display. pressure regulator. Loosen screw and adjust the air shutter until the proper flame appears.Tighten screw. If your oven controls: 1.
PAGE 10
Gas conversions Gas conversions (from Natural gas; or from LR gas to Natural be done by a qualified installer. gas to hE gas) must j Surface burner plastic j cover plastic j cover Natural L.R Fire Hazard Shut off gas supply line Make all conversions before gas supply valve back on. Failure result to follow these in explosion, [] Surface valve. instructions fire can or injury. Complete Remove burner screws holding the burner head down.
PAGE 11
6[] Reinstall Complete the storage installation drawer. steps 9 through Checking for proper cooktop oven flame is very important. You must adjust cooktop burner. 24. burner "LOW" setting See Step 16. and for each The small inner cone should have a very distinct blue flame 1/4" (6 mm) to 1/2" (13 mm) long.The outer cone is not as distinct as the inner cone. LR gas flames may have a slightly yellow tip. If the flame is noisy or blowing, it is getting too much air.
PAGE 12
If range does not if you need assistance: If you need service: operate: if you have questions about operating, cleaning or maintaining your range: Maintain the quality built into your range by calling an authorized service company. To obtain the name and number of the authorized service company: [] Check that the circuit breaker is not tripped or the house fuse blown. [] Check that the power supply cord is plugged into the outlet.