A I R E N G I N E E R E D OPERATING AND INSTALLATION INSTRUCTIONS FOR WHISPAIR RANGEHOODS UTILISING REMOTE FAN MOTOR UNITS
CONGRATULATIONS Congratulations and thank you for choosing a Whispair rangehood. To avoid the risks that are always present when you use an electrical appliance it is important that the rangehood is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.
PRODUCT DESCRIPTION & CARTON CONTENTS CARTON 1 - HOOD UNIT You will be supplied with one of the four hood unit options detailed below. OPTION 1 - INTEGRATED HOOD MODELS INCLUDED: X3M06S5, X3M09S5, X3MD09S5, X3MD12S5 and X3W12S5 INCLUDED IN THE CARTON: 1. Main hood housing including switch control and led lighting 2. Baffle filters 3. Grease trap 4. Cabinet installation screws 5.
OPTION 4 - CEILING MOUNT CASSETTE AND UNIVERSAL HUNG HOOD MODELS INCLUDED: X9C12S5 and X5C10S5 INCLUDED IN THE CARTON: 1. Main hood housing including switch control and led lighting 2. Baffle filters 3. Grease trap 4. Mounting Beams (2x) 5. Threaded rod (4x) and nuts 6. Fixing screws 7.
PRODUCT DESCRIPTION & CARTON CONTENTS CARTON 2 - FAN MOTOR UNIT You will be supplied with one of the two fan motor unit options detailed below. OPTION 1 - INLINE FAN SOLUTION (FIG. A) MODELS INCLUDED: IL-800 and IP-1140 Unit designed to be located in a roof space and then ducted to an external vent to the outside atmosphere. INCLUDED IN THE CARTON: 1. KLEENAIR Inline fan motor unit 2. Mounting bracket 3. Mounting screws for vent and fan motor unit 4. Pipe Clamps - 200mm (4x) 5.
CONDITIONS OF USE AND MAINTENANCE This rangehood is a domestic appliance which has been manufactured and tested to comply with Australian and New Zealand Standard AS/NZS 60335.2.31 and is designed to work under Australian and New Zealand conditions. The hoods are designed to remove bi-products of cooking – heat, steam, grease and odour. This appliance is intended for domestic application only. Any other usage is at the owner’s risk and could be dangerous.
DUCTING AND EXTRACTION LEVELS WHISPAIR ducting is designed to ensure optimum performance for your rangehood. Please follow the installation instructions carefully. Every WHISPAIR rangehood must be ducted to the Inline or Externally mounted KLEENAIR fan motor unit by the use of non-flammable ducting. The rangehood must not be ducted into a wall cavity or a ceiling space where a build-up of grease can occur and become a potential fire risk.
NOISE LEVELS & EXTRACTION LEVELS All KLEENAIR fan motor unit operates at maximum external sound pressure level between 43dB(A) and 76dB(A). The internal operation of the systems will have a varying sound level dependent on the style of hood, the motor option selected, the acoustics of the environment and the installation method used.
PART 1: HOOD INSTALLATION GUIDE Integrated Hood Models included: X3M06S5, X3M09S5, X3MD09S5, X3MD12S5 and X3W12S5 WARNING DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS. STEP 1: To install into your overhead cupboard, several holes may need to be cut into shelves to enable the ducting to exit the cabinetry.
PART 1: HOOD INSTALLATION GUIDE STEP 6: Using the ten (10) fixing holes, screw the Main Chassis into position. STEP 7: Once the Main Chassis is secured into the cabinetry, the Fascia can then be slid back inside the Main Chassis. Replace the screws (removed in Step 3) to fix the Fascia back into positon. STEP 8: Attach the male power plug of the rangehood unit to mains power supply. Note to electricians: Standard 10 Amp General Power Outlet (GPO) required. Position GPO as close to the hood unit as possible.
PART 1: HOOD INSTALLATION GUIDE Wall Hung Canopy Hood Models included: X5L09S5, X5S09S5, X5V09S5, X5R09S5, X5M10S5 and X5N12S5 WARNING DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS. STEP 1: Measure the height (H1) of the hood from the base to the top of the Mounting Hooks.
PART 1: HOOD INSTALLATION GUIDE STEP 6: Secure the hood to the wall by screw fixing through the five (5x) holes on the horizontal plate of the Mounting Bracket. Chimney Bracket Chimney Fixing Points STEP 7: Secure the Chimney Bracket to the wall. STEP 8: Refer to Part 2: Motor Installation Guide. STEP 9: Place the stainless steel chimney on the hood and secure to the Chimney Bracket with the two (2) screws supplied.
PART 1: HOOD INSTALLATION GUIDE Island Hung Canopy Hood Models included: X7S09S5, X7V09S5, X7R09S5 and X7N12S5 WARNING DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS. STEP 1: Using a weighted string line (plumb line), determine the central position of hood on the ceiling.
PART 1: HOOD INSTALLATION GUIDE STEP 6: Refer to Part 2: Motor Installation Guide. STEP 7: Lift the stainless steel chimney into position and secure to the Ceiling Bracket with the four (4) screws supplied. If the chimney is required to be shortened, new holes may need to be drilled to secure the chimney cover. STEP 8: Attach the flexi-ducting to the top of the hood unit and fix into place with a stainless steel clamp (provided).
PART 1: HOOD INSTALLATION GUIDE Ceiling Mounted Cassette and Universal Hung Hood Models included: X9C12S5 and X5C10S5 WARNING DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS. STEP 1: Using a weighted string line (plumb line), determine the central position of hood on the ceiling.
PART 1: HOOD INSTALLATION GUIDE STEP 6: Lift and attach the hood unit to the base of the threaded rod with the provided nuts and washers. Secure the hood cassette firmly to the underside of the ceiling. Level the unit off by tensioning the 10mm nuts. Being mindful not to over tighten. Minimise how much threaded rod is below the nut. Excess threaded rod may interfer with the baffle filters.
PART 2: FAN MOTOR INSTALLTION GUIDE Roof EXTERNAL KLEENAIR MOTOR SOLUTION Roof (Upper) and Wall (Lower) Mounted Flashing to suit Metal or Tile Roof (Optional Accessory) Housing Mounts (Optional Accessory) Fan Power Supply Attached to Internal Hood Unit Ducting Pulled Tight Gentle Bend In Ducting 200mm Ducting Attached to Internal Hood Unit Outlet 108 17 185 440 Wall 702 Fan Power Supply Attached to Internal Hood Unit Gentle Bend In Ducting 60 Ducting Pulled Tight 200mm Ducting Attached to Intern
PART 2: FAN MOTOR INSTALLTION GUIDE Inline Solution Models included: IL-800 and IP-1140 Positioning your KLEENAIR Unit: It is recommended that the KLEENAIR INLINE unit be mounted in a roof space or wall cavity. Please ensure that the KLEENAIR unit is positioned in an environment that is free of other gases to enable an efficient expulsion of the cooking by-products and to ensure that back draft of external gases doesn’t take place.
PART 2: FAN MOTOR INSTALLTION GUIDE External Solution - Wall Mounted Models included: EL-800, EP-1140 and EPP-2010 Cover Positioning your KLEENAIR Unit: It is recommended that when the KLEENAIR EXTERNAL UNIT is WALL mounted, it is positioned a minimum 1800mm above the ground surface with a downward clearance of 1200mm and with a radial clearance of 600mm.
PART 2: FAN MOTOR INSTALLTION GUIDE External Solution - Roof Mounted Models included: EL-800, EP-1140 and EPP-2010 Positioning your KLEENAIR Unit: It is recommended that when the KLEENAIR EXTERNAL UNIT is ROOF mounted, it is positioned a minimum 2100mm above the ground surface with a radial clearance of 600mm.
OPERATION Operating your 4-button control panel Models included: Electronic Control or Touch Control TURNING THE EXTRACTION FUNCTION ON OR OFF: • In standby mode, press button 2 or 3 to change the speed. • The hood has three speed options and a 4th boost speed (4 speeds in total). • The LED indicators directly above the buttons indicates the speed setting selected. • To turn hood off, press button 2 repeatedly until hood returns to standby mode.
PRODUCT CARE It is recommended that your WHISPAIR rangehood and all of its items be cleaned regularly. Before any cleaning or maintenance work, disconnect the cooker hood from the mains power supply. CLEANING THE STAINLESS STEEL HOOD UNIT • It is expected that the stainless steel is cleaned with a quality non-abrasive stainless steel cleaner. • Use a soft cloth for application. • It is recommended that this is performed every 4 weeks.
WARRANTY Every WHISPAIR rangehood comes with a 5-Year parts and labour warranty. This warranty is conditional upon the appliance being used only for personal, domestic and household purposes and installed and operated in accordance with WHISPAIR instructions. The consumer is responsible for any charges associated with removal of the faulty unit and installation of the new unit. The customer may also be responsible for any freight charges incurred in this change over process.
NOTES 23
NOTES 24
Print Version: W_16_S5_01 head office. Haus Group Australia Pty Ltd 2/2 Network Drive CARRUM DOWNS Victoria Australia 3201 Australia. t. (AU) 03 8593 9600 f. (AU) 03 8593 9699 e. info@hausgroup.com.au w. www.hausgroup.com.au New Zealand. t. (NZ) 09 887 6959 f. (NZ) 09 887 6958 e. info@hausgroup.co.nz w. www.hausgroup.co.
