WBU-800 User Guide BACK-UP CAMERA INSTALLS IN MINUTES Product Marketing Name: Camera Hardware Version Identification Number: WBU-800C Product Marketing Name: Monitor Hardware Version Identification Number: WBU-800M
Because the WBU-800 is truly wireless and does not tap into your vehicle's transmission or backup light, you must tell the unit when you are backing up. This also allows you to use your back up camera to view behind the vehicle at any time. When power is applied to the monitor an image will be present for 60 sec by default or the user selected time, if the screen goes blank and more time is required press the for an image to return to the monitor.
TABLE OF CONTENTS Components............................................................................. 4 Getting Started..................................................................... 5-6 Test the Camera / Pairing.................................................... 7-8 Assembly / Installation............................................................ 9 Attach to Vehicle................................................................... 10 Mounting the Monitor.......................................
COMPONENTS 2 1 9 3 5 4 6 7 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
GETTING STARTED The WBU-800 is equipped with a built-in rechargeable lithium battery and is connected with two solar panels that trickle charge the built-in lithium battery when sunlight is available. This will minimize or eliminate the need to manually charge the unit during the year. A USB charging port is provided to initially charge the battery prior to mounting on your vehicle as well as to recharge if needed.
GETTING STARTED Charge The Camera 1. Connect the supplied USB cord to the micro USB port of the camera assembly. 2. Plug the USB cable into any standard USB charger with an output rating of 500ma or higher. The power switch will illuminate when charging. 3. Charge the camera for 5 to 6 hours. When charging is complete, illumination of the power switch will turn off. 4. Close USB door securely to ensure waterproof integrity.
TEST THE CAMERA / PAIRING Test the Camera Prior to attaching the license plate to your vehicle, follow the steps below to ensure pairing between the backup camera and monitor. 1. Slide the switch on the rear housing of the camera to the On position. 2. With power applied to the monitor, the top right button will illuminate to indicate the monitor is ON. 3. The top right button will blink briefly to indicate that it is attempting to communicate with the camera.
TEST THE CAMERA / PAIRING PAIRING MONITOR TO CAMERA Your WBU-800 should automatically pair with your monitor. If your monitor does not automatically pair with the camera after initial charge, the following steps are to be used. NOTE: There are two ways to pair the camera, select the one that works best for your situation. 1. Turn off the camera using the switch on the back of the camera. If already mounted to vehicle skip step 1. 2. Power on monitor. 3.
ASSEMBLY / INSTALLATION Unit is assembled at the factory for mounting along top edge of License plate. See Disclaimer section of this user guide before mounting to vehicle. NOTE: If you will be attaching the unit to the bottom of your license plate, please follow the steps below: 1. Locate then remove the four screws holding the bracket onto the camera. 2. Flip bracket, use the four screws to attach to back of camera.
ATTACH TO VEHICLE Attach license plate to vehicle Once you have tested the camera system and ensured the pairing between the backup camera and monitor, you are ready to reattach the license plate to your vehicle. Use your OEM license plate mounting hardware when mounting license plate to vehicle. NOTE: Be sure to adjust the height of the camera assembly to not impair readibility of the state, registration decal, stamp, or other device indicating the month and year in which the vehicles registration expires.
MOUNTING THE MONITOR Find a mounting surface inside the vehicle for the monitor where it can be easily seen, and does not obstruct your vision when driving. NOTE: To maximize the effectiveness of the suction mount, the mounting location surface temperature should be between 50° and 100°F. Avoid application below 50°F. NOTE: Before mounting the monitor, test the reception of the camera signal in several selected locations within easy reach as one may have better reception than another.
SETUP Functions of the Buttons Press to enable or cancel the video on the monitor. Press for 3 seconds to turn on/off the backup assist lines. Press to enable/cancel the menu. Press to move to or adjust a corresponding function. Press and hold for 3 seconds to turn monitor off.Touch to select a corresponding function. Press to move to or adjust a corresponding function. Adjusting Monitor Settings 1. Press to bring up the menu options 2. Press or arrow to scroll through the different options 3.
MONITOR SETTINGS User selectable camera time durations The WBU-800 has four user selectable camera time durations. You may choose to set the monitor to stay on for 30, 45, 60, or 120 seconds by following the below steps when the monitor is powered on: 1. Press the 2. Press the or to move the cursor over SETUP 3. Press the to select SETUP 4. Press the or to move the cursor over TIME-OUT 5. Press the to select TIME-OUT 6. Press the or to move the cursor over your preferred time duration 7.
MONITOR SETTINGS Menu Operations Press main Menu and 4 options are available including IMAGE PARAMETERS, IMAGE ROTATION, SETUP and SOFTWARE INFORMATION. Press or to select corresponding option, and then press the to enter the option. Select camera 1 for rear camera option or camera 2 for front camera option if your model is such equipped. In the example above the IMAGE PARAMETERS (Brightness, Contrast, Color) Setting Interface is shown.
MONITOR SETTINGS Brightness/Contrast/Color Settings Press or on the interface to adjust the brightness as shown above. Image Rotation Select IMAGE ROTATION, and then press to rotate or mirror the image. (It is best to have a video image displayed when making this selection). If you rotate the image on the display an orange box with arrows will appear . Setup Select SETUP, press to enter SETUP Mode. Pairing mode and camera time duration is found within SETUP menu.
TROUBLESHOOTING If the monitor does not turn on when power is applied: • Check to make sure the power source is active (if your 12V power port is switched with the vehicle ignition, your monitor will only work when the vehicle is running or the key is in the ON position) • Check to make sure the fuse and power cord are in working order button.
DISCLAIMER The Whistler Digital Wireless Backup Camera is intended to assist responsible drivers but it does not relieve a driver from full responsibility for the operation of the vehicle. It is the driver’s sole responsibility to avoid contact with any objects, animals, or persons.
SAFETY Safety If at any time the backup camera assembly becomes damaged, hot or begins to swell, discontinue use immediately. Quickly and safely remove the backup camera from the vehicle. Do NOT continue to handle, attempt to use, or ship the damaged backup camera assembly. Failure to follow these procedures can cause damage to personal property or cause serious injury. Damaged or swollen batteries in the backup camera assembly can be unstable and very hot. DO NOT touch the batteries until they have cooled.
CARE AND MAINTENANCE Cleaning Do not clean or wipe the Back-Up Camera with solvents or chemical materials. If necessary, remove dirt or stains using a soft cloth dampened with a mild detergent solution. Fuse Replacement 1. Turn the cap on the tip of the power plug counterclockwise (no tools needed). 2. Remove the cap, center pin and fuse. 3. Replace the fuse with a new 1-amp fuse. 4. Replace the center pin and cap. Turn the cap clockwise. Disposal The Back-Up Camera is designed to provide years of service.
FCC AND IC INFORMATION IMPORTANT: FCC (Federal Communications Commission) requirements state that changes or modifications not expressly approved by Whistler could void the user’s authority to operate the equipment. FCC Part 15.19 Warning Statement This device complies with part 15 of the FCC rules.
FCC AND IC INFORMATION RF warning statement: The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. FCC ID : HSXBU02M / HSXBU02C IC Warning: This device complies with Industry Canada licence-exempt RSS standard(s).
SPECIFICATIONS CAMERA Operational Current (when transmitting): <220mA Pixels: 640 x 480 View Angle: 110° Image Sensor: 1/4“ CMOS VGA Image Quality: Max 25 fps Camera Assembly: IP65 Battery: 3.7V 2600mAh (non serviceable) TRANSMITTER Frequency: 2400 ~ 2485.5MHz RF transmission distance: >328 ft. (>100 m) unobstructed Operation/storage temperature: 14° to 122°F (-10° to 50°C) MONITOR LCD display screen size: 4.3 in.
WARRANTY INFORMATION Consumer Warranty This Whistler product is warranted to the original purchaser for a period of one (1) year from the date of original purchase against all defects in materials and workmanship, when purchased from an authorized Whistler retailer. This limited warranty is void if the unit is abused, misused, modified, installed improperly, or if the housing and/or serial numbers have been removed.
WARRANTY INFORMATION Service Under Warranty During the warranty period, defective units will be repaired or replaced (with the same or a comparable model), at Whistler’s option, without charge to the purchaser when returned prepaid, with dated proof of purchase to the address below. Units returned without dated proof of purchase will be considered out of warranty and therefore are not covered by the described Limited Warranty. (Refer to Service Out-of-Warranty section.
WARRANTY INFORMATION IMPORTANT: Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your unit insured with return receipt requested. CODs will not be accepted! 2. Include with your unit the following information, clearly printed: • Your name and physical street address for shipping (no PO Boxes), a daytime telephone number, and an email address (if applicable). • A detailed description of the problem (e.g.,“device will not power ON”).
WARRANTY INFORMATION Service Out-Of-Warranty Units will be repaired at “out-of-warranty” service rates when: • The unit’s original warranty has expired. • A dated proof of purchase is not supplied. • The unit has been returned without its serial number. • The unit has been misused, abused, modified, installed improperly, or had its housing removed. The minimum out-of-warranty service fee for your Whistler product is $50.00.
WARRANTY INFORMATION IMPORTANT: When returning your unit for service, be certain to include a daytime telephone number and an email address (if applicable). Customer Service If you have questions concerning the operation of your Whistler product, or require service during or after the warranty period, please call Customer Service at Toll Free (800) 531-0004 Tel (479) 273-6012 Representatives are available to answer your questions Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or visit the FAQs at www.
CORPORATE HEADQUARTERS 1716 SW Commerce Dr. Ste. 8 Bentonville, AR 72712 Toll Free (800) 531-0004 TEL (479) 273-6012 www.whistlergroup.com CUSTOMER RETURN CENTER 1412 South 1st St. Rogers, AR 72756 Email: support@whistlergroup.com 08C19 © 2019 The Whistler Group, Inc.