SERVICE MANUAL 8kg Condenser Tumble Dryer White Knight - B96M8W UK Trouble Shooting & Safety Guide Wiring Diagram Exploded Views Parts List October 2015 Note: Please read before servicing the unit.
CONTENTS – B96M8W 2. User error checklist 3. Control panel connection diagram 3.1 Lack of display on control panel 3.2 Drum does not turn but the control panel displays correctly 3.3 Heating system failure 3.4 The drum turns but the appliance fails to dry 3.5 The dryer makes an abnormal noise when operating 3.6 The dryer produces an abnormal smell when operating when the dryer is operating 3.7 The LED displays 3.8 Error warning codes 4.1 Disassembly warnings 4.2 Disassembly methods 5. Wiring diagram 6.
. Control panel connection diagram P0 P1 P2 P3 P4 P5 P6 P7 Live and neutral Load moisture sensor Motor L + heater (700W) L Drum light and pump Door switch Heater N+ motor N Heater (1600W) L Water level sensor, Inlet thermistor and Exhaust thermistor
3. FAULT FINDING 3.1 Lack of display on control panel Check if power is getting to the appliance NO YES Check fuse for continuity Replace fuse YES Switch off the appliance Check for 230V between pins P0 on PCB NO Check power cord and loom harness for damage YES Replace the PCB YES Replace the mains cable or loom harness as necessary YES Check the RFI filter for damage 3.
Check loose connections or damage to loom Re-assemble or replace the loom 3.3 The heating system does not work YES Check if the “cool” program is in operation Re-test the appliance in a heating program NO YES Check if terminal P4 is loose Re-attach terminals NO YES Check if the loom is damaged Replace the loom harness NO YES Check if the Inlet thermostat on the heater assembly is damaged Replace the heater subassembly 3.
3.
3.7 The LED displays when the dryer is operating YES Check if the bottle is full Empty the bottle NO YES Check if the pump is connected correctly Check PCB for any signs of damage Attach the terminals accordingly or replace the loom Check connections on PCB and replace if necessary NO YES Check if the pump is damaged or blocked Replace or clean the pump NO YES Check if the water level sensor is damaged Replace the water level sensor 3.
4.2 Disassembly methods 1. Control panel assembly disassembly 1. Unfasten the two screws at the rear of the top cover and slide top cover backwards 2. Remove the bottle 3. Remove 4 screws at the front of the dryer from the control panel and cross brace 4. Remove 2 screws inside the slots on the control panel 5.
6. Remove the screws holding the PCB to the control panel. The PCB’s can be removed by unscrewing and unclipping where necessary. 2. Disassembling the RFI filter and water level sensor Disassembling the RFI filter: Remove the loom terminals from the filter. Unfasten the two screws from the filter in order to remove the filter from the upper bracket.
4) Push the two pins of the hinge to separate the hinge.. 4. Disassembling the heater 1) Remove the screws from the rear panel 2) Remove the screws from the air ductwork below the heater 3) Remove the top cover by unscrewing the screws at the back of the appliance.
6) Remove the cable clamp holding the wires to the backpanel 7) Remove the screws from the heater 5. Disassembling the drum 1) With the side panels and the top cover of the appliance removed, remove the bracing struts between the front and backpanels. Remove the screws which hold the metal backpanel to the plastic base. The drum and the backpanel should now come away as one item. 2) Remove the main drive belt from the drum subassembly.
5) Remove the nut with adjustable wrench or similar 6) Remove the drum shaft ring 7) Remove the backpanel from the drum 8) Remove the other two shaft rings
5. Wiring Diagram 1-Pump 2-Drum light 3-Door Switch 4-Moisture level sensor 5-Mains cable 6-RFI filter 7-Motor 8-Capacitor 9-Heater 10-Inlet thermistor 11-Water level sensor 12-Exhaust thermistor 6.
B96M8W - Exploded View - Control Panel - 1.1-1.3 1.3 1.2 1.
B96M8W - Exploded View - Door - 2.1-2.9 2.6 2.5 2.7 2.4 2.3 2.2 2.8 2.1 2.
B96M8W - Exploded View Condenser - Items 3.1 - 3.4 3.1 3.2 3.3 3.
B96M8W - Exploded View - Front Support - 4.1-4.12 4.2 4.3 4.4 4.5 4.6 4.1 4.7 4.12 4.10 4.11 4.9 4.
B96M8W - Exploded View Base - Items 5.1 - 5.18 5.6 5.7 5.5 5.4 5.8 5.3 5.9 5.10 5.2 5.11 5.1 5.12 5.18 5.13 5.14 5.17 5.16 5.
B96M8W - Exploded View - Drum - 6.1-6.5 6.2 6.1 6.3 6.4 6.
B96M8W - Exploded View - Items 7 - 27 15 14 10 13 12 11 9 17 16 8 7 27 26 18 19 21 25 22 24 23 20
B96M8W - Exploded View - Rear Cover - 16.1-16.3 16.3 16.2 16.
B96M8W ITEM DESCRIPTION CODE BOM code 1 1.1 1.2 1.3 2 2.1 2.2 2.3 2.4 Control Panel Subassembly Cycle Select Knob Control Panel Assembly PCB Door Subassembly Outer Frame Protect Cover Window Door Inner Ring Seal 4213 092 64861 4213 092 64871 4213 092 64881 4213 092 64891 4213 092 64901 4213 092 64911 4213 092 64921 4213 092 64931 4213 092 64941 3011608A0039 301160760018 3011607A0145 302460860001 301160700018 301160700053 301160700057 301160700056 302760700005 2.5 2.
B96M8W 5.18 6 6.1 6.2 6.3 6.4 6.