by White-Rodgers Electronic Air Cleaner 240 Volt 50/60 Hz SST Super Slim Twin DGERS WHITE-RO TWIN SUPER SLIM AIR CLEANER ELECTRONIC Model Number 10C27S-010 14C27S-010 20C27S-010 OPERATING LIGHT OFF ON UST Universal Slim Twin Model Number 16C27S-010 OWNERS MANUAL • • • • • Installation Operation Basic SST/UST Service Guide Technical Repair Guide Repair Parts Please read and familiarize yourself with the contents of this manual before installing, operating or performing maintenance on the unit.
1. Read the Owners Manual and the Rules for Safe Operation carefully. Failure to follow these rules and instructions could cause a malfunction of filter or unsatisfactory service. 2. Follow a regular service and maintenance schedule for efficient operation. RULES FOR SAFE INSTALLATION AND OPERATION Please read instructions before installing and using the Electronic Air Cleaner. This will help you obtain the full benefit from the Electronic Air Cleaner you have selected.
HOW THE AIR CLEANER WORKS A Dirt particles flowing through the ducts (Figure 1) first enters the pre-filters (A) where large particles (hair, lint, etc.) are trapped. Smaller particles (smoke, dust, pollen, etc.) pass through these pre-filters and enter the ionizing section (B). Here each tiny particle receives a positive electrical charge. These charged particles then enter the collecting section (C).
PREINSTALLATION Not to Exceed 20° (Interchangeable) (Interchangeable) Collecting Cell Collecting Cell Outlet Box Cabinet Power Pack Handle Air Flow Air Flow Furnace Opening Electronic Air Cleaner Opening Furnace Transition Section (if Needed) Contact Button Pre-Filters (Interchangeable) Electronic Air Cleaner Contact Button See text for Cell Removal Clearance Figure 4 Figure 3 LOCATING THE AIR FILTER Your air filter must be mounted in the return air duct of a central forced-air system, on the ai
TYPICAL MOUNTING POSITIONS Air Flow Air Flow Air Flow Rear View Rear View Figure 6 Figure 8 Figure 7 BASEMENT FURNACE (LOWBOY) (Figure 6) HIGHBOY FURNACE (Figure 8) COUNTERFLOW FURNACE (Figure 7) Cleaner is mounted horizontally in return plenum, just above furnace. Cleaner is mounted horizontally in return duct or plenum, just above furnace. Side installation. Cleaner is mounted vertically, where return air enters side inlet of furnace. HIGHBOY FURNACE (Figure 9) Installation beneath furnace.
INSTALLATION REMOVE OLD FILTER AND DISCARD (Figure 12) NOTE: This filter may be mounted in the furnace compartment. CLEAN BLOWER COMPARTMENT Figure 12 It is suggested that the furnace blower compartment, blower and blower housing be cleaned to ensure clean air circulation. INSTALLATION Frame Duct The following is a typical installation of the air cleaner on a “Highboy” furnace (Figure 8). 1. Place the air filter cleaner on the floor. Stand it upright with the power door facing you (Figure 4).
WIRING INSTRUCTIONS ! 7. With the cabinet installed, the air cleaner can now be wired to electrical input source. ! CAUTION Electrical power to the furnace should be turned off or disconnected at the circuit breaker. WARNING 8. The air cleaner must be wired through the furnace controls to a 240 VAC 60 Hz electrical source. Ensure that electrical connections to the air cleaner are installed properly (see Figure 17). The air cleaner should not have power unless the furnace blower is on.
9. Remove junction box cover and install the required bushing into the 3/4 in. Knock out. With the supply voltage turned off, route three (3) wires into junction box for connections. (See Fig. 19.) Insure all wires are clamped, wire connectors properly installed and grommets used to prevent wire abrasion. 10. With the cabinet Installed, reinstall pre-filter(s) and collecting cell(s) (Figure 20).
A moderate amount of arcing or “snapping” may occur at this time, which will indicate that the cell(s) are still damp. If the noise is objectionable, push the ON-OFF switch to the “OFF” position and allow additional time for cell(s) and pre-filter(s) to dry. In some cases the Operating Light will remain OFF during this initial activation of the air cleaner, and this would indicate that the cell(s) are not completely dry.
SPECIFICATIONS SPECIFICATIONS 10C27S-010 14C27S-010 16C27S-010 20C27S-010 Rated Capacity 600 - 1200 cfm 1000 - 1600 cfm 1000 - 2000 cfm 1600 - 2200 cfm Max. Pressure Drop .08 in. W.G. .08 in. W.G. .12 in. W.G. .09 in. W.G. Cell Weight (2) 7 lbs. each (2) 9 lbs. each (2) 9 lbs. each (2) 9 lbs. each Power Pack Weight 9 lbs. 9 lbs. 10 lbs. 10 lbs. Unit Weight 35 lbs. 42 lbs. 38 lbs. 45 lbs.
TECHNICAL REPAIR GUIDE All voltage measurements indicated can be made with a high voltage D.C. probe and a general purpose volt ohm meter. For example: Simpson 260 or equivalent. WARNING ! Do not attempt installation of this unit unless you are familiar with the necessary tools, equipment, utility connections and potential hazards. NOTE: All tests to be performed with the Ozone Reduction Jumper intact. NOTE: When servicing the power pack components, all wiring must be routed to factory specifications.
POWER SUPPLY CHECKOUT PROCEDURE OZONE REDUCTION All electronic air cleaners typically produce a small amount of ozone that is within established limits. Some customers may notice an odor especially at high altitudes or low air flow rates. 1. Turn power switch to the “OFF” position and remove the power pack from cabinet. 2. Place power pack on a well insulated workbench.
NOTES 13
REPAIR PARTS 14 14
REPAIR PARTS PARTS LIST FOR ELECTRONIC AIR CLEANERS When ordering repair parts, always give the following information as shown in this list. 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER 4. The NAME OF ITEM - Electronic Air Cleaner. Always order by “PART NUMBER” . . . Not by “ITEM NUMBER” ITEM NO.
NOTICE TO CONSUMERS White-Rodgers Electronic Air Cleaner Dear Consumer; White-Rodgers would like to thank you for purchasing a White-Rodgers Electronic Air Cleaner or product containing a White-Rodgers Electronic Air Cleaner. Although WhiteRodgers does not extend a warranty directly to consumers, White-Rodgers does extend a warranty to Wholesalers and Original Equipment Manufacturers who use White-Rodgers Products.
