Install Instructions

ManualsBrandsWhite Rodgers ManualsGas Valves & Controls3/4" X 3/4" Gas Valve, 24 VAC, 0.9" Step

36C/36D

HSI, DSI Proven Pilot Gas Valves

PART NO. 37-6516A

0646

INSTALLATION INSTRUCTIONS

Operator: Save these instructions for future use!

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL

INJURY AND/OR PROPERTY DAMAGE.

DESCRIPTION

The 36C/36D series HSI, DSI proven pilot gas valves are

for use on Spark or Hot Surface Ignition systems and

replaces many O.E.M. gas valves. These valves may be

mounted in any position except upside down. Inlet screen

and pilot gas filter provide maximum protection against

chips and dirt. ON/OFF switch and regulator adjustment

(on some models) are on top of valve for quick setup. Large,

easy-grip pipe boss speeds installation.

➀ Wiring diagrams – see pages 4 & 5

LP Internal

Regulator Conversion Reducer Inlet Wiring

Model Coil Gas Pipe Opening Regulator Adjustment Convertible Kit Line Flow Bushing Pressure Side See

Number Voltage Type Size Characteristic Setting Range Nat./LP Included Interrupter Direction Kit Tap Taps Figure ➀

36C74-913 24 VAC Natural

Step 0.9”/3.5” 2.5”–5.0” No No No Str. Thru Yes Yes No 3

36C76-906 24 VAC Natural

2 Stage 1.0”/3.5” 2.5”–5.0” No No No Str. Thru No Yes No 5

Bimetal,

Electric Open

36C76-920 24 VAC Natural

2 Stage 1.3”/3.5” 2.5”–5.0” No No No Str. Thru No Yes No 5

Bimetal,

Electric Open

36C76-962 24 VAC LP

2 Stage 5.0”/11.0” 9.0”–12.0” No No No Str. Thru No No No 5

Bimetal,

Electric Open

36C76-963 24 VAC Natural

2 Stage 2.0”/3.5” 2.5”–5.0” No No No Str. Thru Yes Yes No 5

Bimetal,

Electric Open

36D13-508 24 VAC Natural

2 Stage 1.1”/3.5” Non- No No No Str. Thru No No No 6

Relay, Adjustable

Electric Open

Lo 1.1/Hi 3.5

36D13-905 24 VAC Natural

2 Stage 1.1”/3.5” 2.5”–5.0” No No No Str. Thru No No No 6

Relay,

Electric Open

Lo 1.1/Hi 3.5

36D13-914 24 VAC LP

2 Stage 2.5”/11.0” Non- No No No Str. Thru No No No 6

Relay, Adjustable

Electric Open

Lo 2.5/Hi 11.0

LP Internal

Regulator Conversion Reducer Inlet Wiring

Model Coil Gas Pipe Opening Regulator Adjustment Convertible Kit Line Flow Bushing Pressure Side See

Number Voltage Type Size Characteristic Setting Range Nat./LP Included Interrupter Direction Kit Tap Taps Figure ➀

36C68-923 24 VAC Natural

Fast Open 3.5” 2.5”–5.0” Yes Yes No Str. Thr u Yes No No 3

UNIVERSAL ELECTRONIC IGNITION GAS VALVES One Model Fits Most Applications

Indicates Canadian Model Number



White-Rodgers is a division

of Emerson Electric Co.

www.white-rodgers.com

Summary of content (8 pages)

PAGE 1
36C/36D HSI, DSI Proven Pilot Gas Valves INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION The 36C/36D series HSI, DSI proven pilot gas valves are for use on Spark or Hot Surface Ignition systems and replaces many O.E.M. gas valves. These valves may be mounted in any position except upside down.
PAGE 2
PRECAUTIONS DO NOT BEGIN INSTALLATION UNTIL YOU READ THE FOLLOWING PRECAUTIONS. ! WARNING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. 1. Failure to turn off electric or main gas supply to heating system could cause personal injury and/or property damage by shock, gas suffocation, fire, and/or explosion. 2. Do not use this control on circuits exceeding specified voltage.
PAGE 3
INSTALLATION MAIN PIPING CONNECTIONS Drop NOTE Horizontal All piping must comply with local codes, ordinances, and/or national fuel gas codes. 1. Turn off electrical power to the system at the fuse box or circuit breaker. Also turn off the main gas supply. 2. If replacing an existing valve, disconnect all plumbing and electrical connections from the old control. 3. The valve may be installed in any position except upside down.
PAGE 4
WIRING DIAGRAMS SYSTEM WIRING NOTE REFER TO AND FOLLOW THE APPLIANCE MANUFACTURER'S WIRING DIAGRAM. USE THE TABLE ON PAGE 1 TO IDENTIFY THE PROPER TERMINAL IDENTIFICATION FIGURE FOR THE GAS VALVE. All wiring should be installed in accordance with local and national electrical codes and ordinances. Always check that the electrical power supply used agrees with the voltage and frequency shown on the gas control.
PAGE 5
WIRING DIAGRAMS Wiring for 36C76-906 Gas Valve D-1 REDUNDANT/ PILOT VALVE W-1 W-1 C-1 MAIN VALVE Figure 5 Bi-metal two stage D-1 C-1 W-2 C-2 HI-LO OPERATOR C-2 PILOT ADJ. W-2 Wiring for 36D13-508, -905, & -914 Gas Valves 1 2 Figure 6 Relay two stage 3 REDUNDANT VALVE 3 2ND STAGE RELAY 4 36D13 MAIN VALVE 2 PILOT ADJ.
PAGE 6
INSTALLATION (cont'd) OUTLET PRESSURE REGULATOR ADJUSTMENT FOR VALVES WITH AN ADJUSTABLE REGULATION RANGE The pressure regulator has been factory adjusted (see control for specific setting). Although additional adjustments will not normally be necessary, you may adjust the regulator. Do not force the adjusting screw beyond the limits that it can easily be adjusted. 1. Energize system to ignite main burner. 2. Remove "Reg. Adj." cover screw. 3.
PAGE 7
PARTS & ACCESSORIES Item Number Model Number Description F92-0656 L.P. to natural gas conversion kit for 36C, 36D, 36E and 36F gas valves with regulation range of 2.5 to 5” W.C. F92-0659 Natural to regulated L.P. gas conversion kit for 36C, 36D, 36E and 36F gas valves with regulation range of 7.5 to 12.0” W.C. F92-0737 Item Number Model Number F6-1794 Description Bracket for Bryant pilots when retrofitting with Cycle-Pilot®. / ” brass compression fitting for pilot line connections.
PAGE 8
The Emerson logo is a trademark and service mark of Emerson Electric Co.