White-Westinghouse LAVADO !i Models/Modelos: Made in USA SWX703HS, SWX703HQ, SWS833HS, SWS833HSQ, SWS1233HS, SWS1233HQ, SWS1339HS, SWS1339HQ, SWS1649HS, SWS1649HQ P/N 137123700A (0812)
TABLE OF CONTENTS Important Safety Instructions ................................................................................................................................. Washing Procedures .............................................................................................................................................. Stain Removal ...........................................................................................................................................................
Avoid Grounding type f Do not under any fire hazard or electrical wall receptacle circumstancescut, shock. Do not use an remove,or bypass /_ the grounding prong adaptor plug or _ i v_ from this plug extension cord or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or J Powersupply cord with death.
Important Safety Instructions (con 't) • To _revent injury, do not reach into the washer while parts are moving. Before loading, unloading or adding items, push in the cycle selector knob and allow the tub to coast to a complete stop before reaching inside. • Failure to comply with these warnings could result in serious personal injuries. This washer is equipped with an electrical overload protector. The motor will stop if it becomes overheated.
Washing Procedures(continued) 6. Add laundry load to washer, • Dry load level should not be higher than top row of holes in wash tub. Do not overload washer. • Do not put items on top of agitator or wrap them around it. Load items evenly. Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. When washing a single heavy item, add 1 or 2 towels to balance the load. 7. Do not load items above top row of holes in wash tub.
Stain Removal Safe Stain Removal Procedures To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below: • • Do not combine stain removal products. Follow fabric care label instructions. STAIN Read and comply with all instructions on stain removal products. Keep products in their original labeled containers and out of children's reach. • Thoroughly wash any utensil used.
Common Washing Problems Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing results, follow these suggestions provided by The Soap and Detergent Association. PROBLEM POSSIBLE CAUSES Blue stains ,Detergent or liquid fabric softener did not dissolve or disperse. SOLUTIONS PREVENTIVE • If caused by detergent, mix 1 cup (240 ml) white vinegar with 1 quart (.95 L) water in a plastic container. Soak item 1 hour. Rinse.
Care and Cleaning Use care with laundry products. They can damage finish on the washer. _sMe • Remove items from the washer as soon asthe cycle ends. Excesswrinkling, color transfer, and odors may develop in items left in the washer. Dry the washer top, the area around the lid opening, and the underside of the lid. These areas should always be dry before the lid is closed. • Beforecleaningthewasherinterior, electrical shock hazards.
Avoid Service Checklist Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the result of defective workmanship or materials in this washer. OCCURRENCE POSSIBLE CAUSE SOLUTION "Clunking" sounds. A certain amount of "clunking" or gear sounds are normal in a heavy-duty washer. This is normal. Foreign objects such as coins or safety pins may be in tub or pump. Stop washer and check tub.
OCCURRENCE Wash load too wet spin. POSSIBLE CAUSE after Water does not enter washer or it enters slowly, Washer is overloaded. Do not overload washer. See Procedures. Load is out of balance. Rearrange load to allow proper spinning. Drain hose is kinked. Straighten Washer lid is open. Close washer lid. The washer will not fill with water, agitate or spin when the lid is open, and will only start to do so if the lid is closed. Water supply is not adequate Water open. Water level cover load.