Installation Guide

ManualsBrandsWhitehaus Collection ManualsAppliancesCyclonehaus 1 HP Continuous Feed Garbage Disposal in Polished Chrome

Garbage Disposal

Product Installation Manual

WH007

Before Installing:

NOTE: The Cyclonehaus Garbage Disposal has been designed to

operate on 110 volt, 50/60 Hz exclusively. Using any other voltage or Hz

may affect the garbage disposal

IMPORTANT: Read all instructions thoroughly. Keep this guide for future

reference.

CAUTION: Review safety instructions rst to avoid risk of re,

electrical shock or injury before using disposal.

Tools and Materials You May Need:

• Phillips & Flat Screwdriver

• Hacksaw

• Plumber’s Putty

• Dishwasher Connector Kit

• Hammer

• Pipe Wrench

• Dowel or Steel Punch

• Power Cord

• Strain Relief

Summary of content (8 pages)

PAGE 1
by Garbage Disposal Product Installation Manual WH007 Before Installing: NOTE: The Cyclonehaus Garbage Disposal has been designed to operate on 110 volt, 50/60 Hz exclusively. Using any other voltage or Hz may affect the garbage disposal IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference. CAUTION: Review safety instructions first to avoid risk of fire, electrical shock or injury before using disposal.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS TO AVOID A RISK OF FIRE, ELECTRIC SHOCK OR INJURY. DO NOT THROW AWAY. WARNING - When using electrical appliances, basic precautions should be followed, including the following: 1. Read all instructions before using the garbage disposal. 2. To reduce risk of injury, close supervision is necessary when the garbage disposal is used near children. 3. Do not put fingers or hands into garbage disposal. 4.
PAGE 3
2. EZ MOUNT SYSTEM 7. From underneath the sink, slip fiber gasket (see 1) onto exposed sink flange. With arrows pointing up, screw support ring (see 2) onto the sink flange, hand tighten until the sink flange will not move (see photo H). At this point you may want to insert stopper in sink and fill with water to check sink flange seal and ensure there are no leaks. 8.
PAGE 4
3. GROUNDING INSTRUCTIONS FOR GARBAGE DISPOSALS EQUIPPED WITH A GROUNDED PLUG-IN CORD This appliance must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
PAGE 5
Wiring Disposal Directly to House Current This appliance must be connected to a grounded, metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminator or lead on the appliance. 1. If you use BX cable: a. Install cable connector in hole. b. Connect white wire to white lead of disposal. c. Connect black. d. Connect bare ground.
PAGE 6
. CONNECTING DISPOSAL TO EZ MOUNT 1. Line up disposal under mounting assembly. Guide hopper projections into mount ring slots. Turn mount ring about 1/4” to right so that the disposal is temporarily supported (see photo O). 2. Turn mount ring and disposal until disposal elbow lines up with trap (see photo P). 3. Turn mount ring to the right (counter-clockwise) until it locks up tight. Insert shaft of screwdriver into slot on mount ring and tighten until the lock position is achieved.
PAGE 7
. DISHWASHER CONNECTION If you are utilizing a dishwasher, complete the following procedure. 1. Using a blunt instrument like a steel punch or wooden dowel, knock out entire plug. Do not use a screwdriver or sharp instrument. When knockout plug falls into garbage disposal, remove it. 2. Connect dishwasher hose using hose clamp. If hose size is different, you will need a Dishwasher Connector Kit. Make sure all plumbing connections are tight and in accordance with all plumbing codes and ordinates.
PAGE 8
9. OPERATING INSTRUCTIONS The Anti-Jam Swivel Impellers make a clicking sound as they swing into place. This indicates normal operation. 1. Remove sink stopper. Turn on a medium flow of cold water. 2. Turn switch to ON position; your motor is turning at full speed and ready to use. 3. Scrape in food waste. Down the drain go table scraps, peels, rinds, seeds, etc. To speed up food waste disposal, cut or break up large rinds and cobs.