Installation Guide

Magic Flush
®
Product Installation Manual
WHMFL3309-EB • WHMFL3222-EB • WHMFL3351-EB
Before Installing:
1. Read the instructions carefully to be familiar with the tools, ttings and
installation procedures to prevent any unnecessary damage.
2. Inspect product prior to installation
3. Check whether the rough-in on the installation position is aligned with that
of the toilet. Check all the specications of the pipelines for the water supply.
4. Handle product with care and ensure that the nut is not overtightened.
5. When installing the toilet, make sure the oor is even.
6. If you want to replace the toilet, turn off the water supply and ush the toilet
to make sure no water remains inside the toilet. Remove the soft pipe for
water supply, and unfasten the screws. Remove the toilet and the old gasket
and clean the end of the drainage outlet.
Note: Plug the drainage outlet on the oor if you do not install the toilet
immediately.
7. Make sure the water supply is turned off.
NOTE: 1. We reserve the right to change the features, packing and ttings of
the product without notice.
2. Please keep the installation instructions accessible (including
installation procedure, tting form, troubleshooting, and notice).
3. Closet ange is not included.
Common Tools Needed:
• Adjustable Wrench
• Pipe Wrench
• Tape Measure
• Drill
• Silicone
• 11/64 Drill Bit for Wood
Floor Installation
• 5/16 Drill Bit for Concrete/
Tile Installation
Troubleshooting:
Note:
1. Do not throw newspaper, diapers, sanitary napkins, or similar articles in the toilet bowl.
2. Do not impact the ceramic part heavily in case of any damage.
3. To maintain the normal ushing function of the toilet, please use a long handle nylon brush and a neutral cleanser
to clean up the bowl or pipes to prevent the accumulation of mineral substances. It is suggested to clean your
toilet once a week.
4. Clean the lter at least once a month to prevent slow water inletting or water blockage in the tank.
5. Do not use any cleanser in the tank, otherwise the rubber accessories in the tank may be damaged, causing leakage
Please follow what is specied below to avoid discoloration,
deformation, ne cracks, or scratches on the toilet seat:
1. Do not expose the toilet seat to sunlight or sources of heat
2. Do not use sharp or abrasive materials to clean the toilet seat
3. Do not use corrosive chemicals to clean the toilet seat
Malfunctions Reasons Solution
1. The main water valve does not open
2. Incoming water lter net is clogged
3. Floating ball of water inlet valve in cistern
does not work
1. Higher water pressure
2. Floating ball of water inlet valve does
not work
3. Water inlet valve is broken
4. Floating ball of water inlet valve touches
the inwall of cistern
1. The water level of inlet valve is too low
2. The push button does not reach pushing point
3. Press the wrong button
1. The drainage outlet is not aligned with the
outside drainage pipe
2. Drainage pipes are obstructed
3. Inadequate ushing water
1. The hexangular nuts of water inlet valve
are not fastened
2. The water supply spacer of inlet valve is
damaged
3. The water supply spacer on the bottom of
cistern is damaged
1. Drainage pipes are obstructed
2. Water outlet pipes are obstructed
• No Incoming Water
• Non-Stop Incoming Water
• Inadequate Flushing Water
• Slow Drainage or
Inadequate Suction
• Leakage
• Overow From Drainage Pipe
1. Turn on the valve
2. Clean the net
3. Readjust the oating ball
1. Reduce water pressure
2. Readjust the oating ball
3. Call your dealer to replace
inlet valve
4. Adjust the direction of
oating ball
1. Adjust the water inlet valve
to appropriate position
2. Adjust water level rod
3. Identify small and large
ushing button, or call
your dealer
1. Readjust or reinstall the
product
2. Clean the drainage pipes
3. Adjust the water in cistern
1. Fasten the nuts
2. Change the water supply
spacers
1. Clean the drainage pipes
2. Clean the water outlet pipes