Installation Guide
6363-8371 Gunmetal Covered Closet ©2017 Whitmor, Inc.
P 1 ea
Cover
Assembly
Time: Less
than 1 hour.
This product's
intended use is
for storing clothes.
Tools Needed:
No additional tools required.
STEP 1. Assemble male and female horizontal
tubes (C&D) then assemble two bottom end
tubes (A) by pressing together. Install four floor
glides (L) and four bottom male vertical tubes
(F) using four hex screws (M). Install two more
floor glides (L) and two bottom male
center vertical tubes (H) using two hex
screws (M). Tighten all hex screws with
hex wrench (Q).
STEP 2. Unzip the cover (P) front and carefully
fit holes in bottom of cover over the bottom male
vertical tubes (F&H). Slide the cover down and
carfully lay the cover back. Install one
horizontal support tube (E) with
two hex screws (M) over the
bottom of the cover.
A 2 ea
Bottom end tube
F 4 ea
Bottom male vertical tube
L 6 ea
Floor glide
G 4 ea
Top female vertical tube
H 2 ea
Bottom male center vertical tube
I 2 ea
Top female center vertical tube
J 1 ea
Male hanging tube
K 1 ea
Female hanging tube
B 2 ea
Top end tube
C 4 ea
Female horizontal tube
D 4 ea
Male horizontal tube
E 2 ea
Horizontal support tube
Q 1 ea
Hex wrench
8680 Swinnea Road • Suite 103 • Southaven, MS • 38671
MADE IN CHINA
NEED HELP? For help with assembly, or if you are missing a part,
please call Whitmor’s Consumer Care Team, 1-888-944-8667 between
8 a.m. and 4:30 p.m. (Central Standard Time) Monday through Friday.
Or email: help@whitmor.com. Visit us online at www.whitmor.com
Rev.0 | 06.07.17 Printed in China
Note: For easier
assembly, unzip cover
before installing.
Note: Although your clothes
closet can be assembled by one
person, it is recommended that
two people install the cover.
A
A
F
F
H
L
M
L
L
L
M
M
M
L
M
L
M
D
D
C
C
H
F
F
P
F
F
H
H
F
F
M 16 ea
Countersunk
hex screw
O 2 ea
Hanging tube
hook
N 2 ea
Flat head
hex screw
STEP 3. Install four top
female vertical tubes (G)
and two top female center
vertical tubes (I) onto
bottom male vertical tubes
(F&H). Assemble two top
end tubes (B) to male
and female horizontal
tubes (C&D) by pressing
together. Install this top
section to the tubes (G&I)
using six hex screws (M).
Install one horizontal
support tube (E) with two
hex screws (M). Install the
hanging tubes (J&K) to
hanging tube hooks (O)
using two flat head hex
screws (N). Hang the
hanging tube hooks (O)
overt the top end tubes
(B). Tighten all hex screws
with hex wrench (Q).
B
G
G
G
I
I
C
C
D
D
G
B
J
K
M
M
M
M
M
M
M
M
N
N
O
O
Part Reference
A
B
C
D
E
F
G
H
I
F9339
F9338
F9343
F9342
F9348
F9341
F9340
F9345
F9344
Part Reference
J
K
L
M
N
O
P
Q
F9346
F9347
F9350
F9349
F9399
F9400
F9351
F9401
STEP 4. Lift the cover (P) up over the top of
the frame, carefully fitting the corners of the
cover over the top corners of the frame. Slide
the bottom of the cover downwards evenly to
the base of the frame.
STEP 5. Zip up the cover
front and the assembly is
complete.
P
E
E
M
M
F
F
H
H
F
F