User's Manual
Table Of Contents
- Contents
- Important Information
- Notices
- Description
- Installation
- Configuration
- Overview
- Accessing the Main Menu
- Configuring with the Main Menu
- Unit Identification
- Hardware/Software Revision
- System Software ROM Images
- System Current Status
- Network Configuration
- IP Filter Configuration
- RF Station Configuration
- Viewing Current RF Station Configuration
- Setting the Operating Mode
- General Equipment Setup for Performing RF Tests
- Setting Test Mode Timer Minutes
- Performing Link Monitor Test (Normal Mode)
- Performing Transmit and Receive Tests
- Performing the RSSI Test
- Setting the RF Transmit Status
- Setting the Link Monitor Period
- Setting Maximum Remote Distance (Base Station Only)
- Setting Link Monitor Remote Station Rank
- Adjusting Throttling (Remote Station Only)
- Setting Tx Power Automatically (Remote Station Only)
- Adjusting User Output Power Ceiling (Remote Station Only)
- Setting Signal Margin (Remote Station Only)
- Viewing Current Output Power Level Adjust
- Radio Module Configuration
- Viewing the Radio Module Configuration
- Setting Config Test Minutes
- Setting the Station Type
- Setting the Station Rank
- Setting the Center Frequency
- Setting Security Passwords
- Setting the Scrambling Code
- Setting the Acquisition Code
- Adjusting the Tx Power Level
- Setting a Base to Repeater Mode (Base Station Only)
- Setting System Symmetry Type (Base Station Only)
- Setting Dynamic Polling Level (Base Station Only)
- Setting Remote Unit RF Group
- Rebooting and Saving RF Module Configurations
- RF/Ethernet Statistics
- System Security
- System Commands
- Link Monitor Display
- Logout
- Setting Operating Mode with the Mode Button
- Command Line Interface
- Troubleshooting
- Appendix A: Planning Your Wireless Link
- Appendix B: Using HyperTerminal
- Appendix C: Configuring a Simple Data Network
- Appendix D: SNMP
- Appendix E: Technical Reference Information
- Appendix F: Menu Map
- Appendix G: Upgrading Software
- Glossary
- Index
Using Object Identifier Nodes
JUL 2001 Rev 03
141
repeaterMode 1.3.6.1.4.1.2686.2.1.41 INTEGER Read Only Current base station repeater mode:
0 = disabled, 1 = enabled
systemType 1.3.6.1.4.1.2686.2.1.42 INTEGER Read Only Current base station symmetry:
0 = asymmetric, 1 = symmetric
remoteGroup 1.3.6.1.4.1.2686.2.1.43 INTEGER Read Only Current RF group identifier:
0 = closed, 1 - 63 = special group
numOfPollRounds 1.3.6.1.4.1.2686.2.1.44 INTEGER Read Only Current Number of Polling Rounds (1-60)
txPwrLevelAdj 1.3.6.1.4.1.2686.2.1.45 INTEGER Read Only Current RF Tx Power Level Adjust (-31 to 0 dB)
defStationType 1.3.6.1.4.1.2686.2.1.46 INTEGER Read Only Default Station type: 0 = remote, 1 = base
defStationRank 1.3.6.1.4.1.2686.2.1.47 INTEGER Read Only Default Station RF Rank
defCenterFreq 1.3.6.1.4.1.2686.2.1.48 INTEGER Read Only FLASH RF center frequency
defSecurityWord1 1.3.6.1.4.1.2686.2.1.49 INTEGER Read Only Default RF security password 1
defSecurityWord2 1.3.6.1.4.1.2686.2.1.50 INTEGER Read Only Default RF security password 2
defSecurityWord3 1.3.6.1.4.1.2686.2.1.51 INTEGER Read Only Default RF security password 3
defSecurityWord4 1.3.6.1.4.1.2686.2.1.52 INTEGER Read Only Default RF security password 4
defSecurityWord5 1.3.6.1.4.1.2686.2.1.53 INTEGER Read Only Default RF security password 5
defScramblingCode 1.3.6.1.4.1.2686.2.1.54 INTEGER Read Only Default RF scrambling code word
defAcquisitionCode 1.3.6.1.4.1.2686.2.1.55 INTEGER Read Only Default RF acquisition code (0-15)
Group Parameter Address/Node Syntax Access Description
Frequency
(GHz)
Integer
Frequency
(GHz)
Integer
2.4258 24258 2.4455 24455
2.4302 24302 2.4498 24498
2.4345 24345 2.4542 24542
2.4400 24400