User's Manual
Table Of Contents
- Contents
- Important Information
- Notices
- Description
- Installation
- Configuration
- Overview
- Accessing the Main Menu
- Configuring with the Main Menu
- Unit Identification
- Hardware/Software Revision
- System Software ROM Images
- System Current Status
- Network Configuration
- IP Filter Configuration
- RF Station Configuration
- Viewing Current RF Station Configuration
- Setting the Operating Mode
- General Equipment Setup for Performing RF Tests
- Setting Test Mode Timer Minutes
- Performing Link Monitor Test (Normal Mode)
- Performing Transmit and Receive Tests
- Performing the RSSI Test
- Setting the RF Transmit Status
- Setting the Link Monitor Period
- Setting Maximum Remote Distance (Base Station Only)
- Setting Link Monitor Remote Station Rank
- Adjusting Throttling (Remote Station Only)
- Setting Tx Power Automatically (Remote Station Only)
- Adjusting User Output Power Ceiling (Remote Station Only)
- Setting Signal Margin (Remote Station Only)
- Viewing Current Output Power Level Adjust
- Radio Module Configuration
- Viewing the Radio Module Configuration
- Setting Config Test Minutes
- Setting the Station Type
- Setting the Station Rank
- Setting the Center Frequency
- Setting Security Passwords
- Setting the Scrambling Code
- Setting the Acquisition Code
- Adjusting the Tx Power Level
- Setting a Base to Repeater Mode (Base Station Only)
- Setting System Symmetry Type (Base Station Only)
- Setting Dynamic Polling Level (Base Station Only)
- Setting Remote Unit RF Group
- Rebooting and Saving RF Module Configurations
- RF/Ethernet Statistics
- System Security
- System Commands
- Link Monitor Display
- Logout
- Setting Operating Mode with the Mode Button
- Command Line Interface
- Troubleshooting
- Appendix A: Planning Your Wireless Link
- Appendix B: Using HyperTerminal
- Appendix C: Configuring a Simple Data Network
- Appendix D: SNMP
- Appendix E: Technical Reference Information
- Appendix F: Menu Map
- Appendix G: Upgrading Software
- Glossary
- Index
Appendix D: SNMP
144 AWE 120-24 Installation & Configuration Guide
remoteDistance 1.3.6.1.4.1.2686.2.1.82 INTEGER Read/Write Maximum remote unit distance (km)
linkMonitorRank 1.3.6.1.4.1.2686.2.1.83 INTEGER Read/Write Link monitor remote station rank (1-1000)
throttleEnable 1.3.6.1.4.1.2686.2.1.84 INTEGER Read/Write Throttling enable:
0 = disabled, 1 = enabled
throttleLevel 1.3.6.1.4.1.2686.2.1.85 INTEGER Read/Write RF throttle level (1-50)
config86 1.3.6.1.4.1.2686.2.1.86 INTEGER Read/Write Spare
config87 1.3.6.1.4.1.2686.2.1.87 INTEGER Read/Write Spare
config88 1.3.6.1.4.1.2686.2.1.88 INTEGER Read/Write Spare
config89 1.3.6.1.4.1.2686.2.1.89 INTEGER Read/Write Spare
communityName1 1.3.6.1.4.1.2686.2.1.90 DisplayString
(0..15)
Read/Write Read-only access community name
communityName2 1.3.6.1.4.1.2686.2.1.91 DisplayString
(0..15)
Read/Write Read-Write access community name
ethernetAccess 1.3.6.1.4.1.2686.2.1.92 INTEGER Read Only Ethernet access to local host:
0 = disabled, 1 = enabled
Group Parameter Address/Node Syntax Access Description
Integer
Distance
(km)
Integer
Distance
(km)
15735
2108 40
3159 45
4201050
5251150
6301260