User's Manual
Table Of Contents
- Contents
- Important Information
- Notices
- Description
- Installation
- Configuration
- Overview
- Accessing the Main Menu
- Configuring with the Main Menu
- Unit Identification
- Hardware/Software Revision
- System Software ROM Images
- System Current Status
- Network Configuration
- IP Filter Configuration
- RF Station Configuration
- Viewing Current RF Station Configuration
- Setting the Operating Mode
- General Equipment Setup for Performing RF Tests
- Setting Test Mode Timer Minutes
- Performing Link Monitor Test (Normal Mode)
- Performing Transmit and Receive Tests
- Performing the RSSI Test
- Setting the RF Transmit Status
- Setting the Link Monitor Period
- Setting Maximum Remote Distance (Base Station Only)
- Setting Link Monitor Remote Station Rank
- Adjusting Throttling (Remote Station Only)
- Setting Tx Power Automatically (Remote Station Only)
- Adjusting User Output Power Ceiling (Remote Station Only)
- Setting Signal Margin (Remote Station Only)
- Viewing Current Output Power Level Adjust
- Radio Module Configuration
- Viewing the Radio Module Configuration
- Setting Config Test Minutes
- Setting the Station Type
- Setting the Station Rank
- Setting the Center Frequency
- Setting Security Passwords
- Setting the Scrambling Code
- Setting the Acquisition Code
- Adjusting the Tx Power Level
- Setting a Base to Repeater Mode (Base Station Only)
- Setting System Symmetry Type (Base Station Only)
- Setting Dynamic Polling Level (Base Station Only)
- Setting Remote Unit RF Group
- Rebooting and Saving RF Module Configurations
- RF/Ethernet Statistics
- System Security
- System Commands
- Link Monitor Display
- Logout
- Setting Operating Mode with the Mode Button
- Command Line Interface
- Troubleshooting
- Appendix A: Planning Your Wireless Link
- Appendix B: Using HyperTerminal
- Appendix C: Configuring a Simple Data Network
- Appendix D: SNMP
- Appendix E: Technical Reference Information
- Appendix F: Menu Map
- Appendix G: Upgrading Software
- Glossary
- Index
JUL 2001 Rev 03 151
Appendix F: Menu Map
Wi-LAN AWE 120-24 Main Menu
Unit Identification
Hardware/Software Revision
System Software ROM Images
Current System Status
Network Configuration
IP Filter Configuration
RF Station Configuration
Radio Module Configuration
RF/Ethernet Statistics
System Security
System Commands
Link Monitor Display
Logout
Unit Identification
Serial Number
Production Date
Ethernet MAC Address
Unit Name/Description
Unit Location
Contact Name
System Revision Information
Hardware
ROM Size
RAM Size
Software
File Name
System Software ROM Images
System Current Status
Cumulative Run-Time
Current Run-Time
Successful Logins
Unsuccessful Logins
Local User Logged In
Telnet User Logged In
FTP User Logged In
Network Configuration
Internet IP Address
New IP Address (Reboot Reqd)
Internet IP Subnet Mask
Default Gateway IP Address
SNMP NMS Trap IP Address
MAC Filter Entry Age Time Minutes
IP Filter Configuration
IP Packet Filtering
IP Address Filtering
Default IP Address Filtering
RF Station Configuration
Operating Mode
RF Transmit Status
Link Monitor Period
Test Mode Timer Minutes
Base Station Only Parameters
Maximum Remote Distance
Link Monitor Remote Station Rank
Remote Station Only Parameters
Throttle Enable
Throttle Level
(view only)
System Security
SNMP Community Name 1
SNMP Community Name 2
Change User Password
Confirm User Password
Change Supervisor Password
Confirm Supervisor Password
Ethernet Access to Local Host
Wireless Access to Local Host
Auto Logout Minutes
System Commands
Default System Image
Reboot a System Image
Reboot Current Image
Restore Factory Config and Reboot
Reset Radio Statistics
Reset Ethernet Statistics
RF Link Monitor Statistics
RF Ethernet Statistics
(view only)
(view only)
Radio Module Configuration
Station Type
Station Rank
Center Frequency
Security Password 1
Security Password 2
Security Password 3
Security Password 4
Security Password 5
Scrambling Code
Acquisition Code
Config Test Minutes
Base Station Only Parameters
Repeater Mode
System Symmetry Type
Dynamic Polling Level
Remote Station Only Parameters
Remote Unit RF Group
Reboot New RF configuration
Save Current Config to Flash
Tx Power Level Adjust
Link Monitor/Output Power
User Output Power Adjust Ceiling
Signal Margin
Current Output Power Level Adjust
Factory Output Power Adjust
Ceiling